![background image](http://html1.mh-extra.com/html/ozito/pxcjbls-0182u/pxcjbls-0182u_original-operating-instructions_1666208011.webp)
GB
- 11 -
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED blinks:
The battery is empty, recharge the battery.
All LEDs blink:
The battery pack has undergone exhaustive di-
scharge and is defective. Do not use or charge a
defective battery pack.
Important!
The equipment‘s operating time depends on
the battery with the lower charge level or lower
capacity (Ah). Therefore, only use rechargeable
batteries which are charged to the same level and
have the same capacity (Ah). Never combine full
and half-full batteries or batteries with di
ff
erent
capacities (Ah). Always charge the two batteries
simultaneously before starting to use them.
5.5 Fitting the harness (Fig. 3c/3d)
Fasten the harness to the eyelet on the motor
housing. Place the harness over your shoulder
and adjust the length to that you can guide the
equipment comfortably.
Caution: Carry the harness so that the click
fastener is always within reach. In an emer-
gency you can quickly remove the equipment
by opening the click fastener (Fig. 3d / Item
B).
6. Operation
6.1 Switching on the equipment (Fig. 6)
•
To switch on, press and hold the On/Off
switch (2).
•
To switch off, let go of the On/Off switch.
•
Channel the air stream forward and walk
slowly to blow foliage or garden refuse into a
pile or to clear out hard-to-reach places.
6.2. Speed control (Fig. 6)
The equipment is
fi
tted with an electronic speed
controller. To use it, turn the speed controller
(Fig. 6/Item 6) to the desired position. Use the
equipment only with the speed which is actually
required and never let it run at a speed which is
faster than necessary.
6.3 Turbo mode (Fig. 6)
If you need more blowing power, e.g. to blow
away piles of wet foliage, you can press the turbo
button (Fig. 6 / Item 5). Pressing the turbo button
will raise the speed and therefore the blowing
power temporarily.
Important: To reduce noise and prolong bat-
tery operating time, never actuate the turbo
button longer than necessary.
7. Cleaning, maintenance and
ordering of spare parts
Danger!
Always remove the batteries before you carry out
any cleaning work.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
7.2 Maintenance
•
Should the tool experience problems beyond
those mentioned above, let only an autho-
rised professional or a customer service shop
perform an inspection.
•
There are no other parts inside the equipment
which require maintenance.
7.3 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info
Anl_PXCJBLS_0182U_SPK7.indb 11
Anl_PXCJBLS_0182U_SPK7.indb 11
26.08.2019 05:57:12
26.08.2019 05:57:12
Содержание PXCJBLS-0182U
Страница 18: ... 18 Anl_PXCJBLS_0182U_SPK7 indb 18 Anl_PXCJBLS_0182U_SPK7 indb 18 26 08 2019 05 57 13 26 08 2019 05 57 13 ...
Страница 19: ... 19 Anl_PXCJBLS_0182U_SPK7 indb 19 Anl_PXCJBLS_0182U_SPK7 indb 19 26 08 2019 05 57 13 26 08 2019 05 57 13 ...
Страница 20: ... 20 Anl_PXCJBLS_0182U_SPK7 indb 20 Anl_PXCJBLS_0182U_SPK7 indb 20 26 08 2019 05 57 13 26 08 2019 05 57 13 ...
Страница 21: ... 21 Anl_PXCJBLS_0182U_SPK7 indb 21 Anl_PXCJBLS_0182U_SPK7 indb 21 26 08 2019 05 57 13 26 08 2019 05 57 13 ...