Ozito PXCJBLS-0182U, Оригинальная инструкция по эксплуатации

Страница: 10 / 22

GB
- 10 -
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment’s construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
5. Before starting the equipment
Caution!
The equipment is supplied without batteries and
without a charger is allowed to be used only with
the lithium-ion batteries of the Power-X-Change
series!
The lithium-ion batteries of the Power-X-Change
series are allowed to be charged only with the
Power-X charger.
Warning!
Always remove the battery pack before making
adjustments to the blower tube.
5.1 Fitting the blower tube (Fig. 3a/b)
There are three settings for adjusting the length
of the blower tube to your requirements. To do
so, attach the blower tube to the motor unit. The
groove (A) must be pushed into the guide (B)
when you do this. When the blower tube has
reached one of the three end points on the motor
unit, turn it to the right to secure it in position on
the motor unit.
Important! The tube must be turned as far as
it will go to make sure it is fi rmly securely in
position.
5.2 Fitting the battery pack (Fig. 4)
Press the pushlock button of the battery pack as
shown in Fig. 4 and push the battery pack into the
mount provided. When the battery pack is posi-
tioned as in Fig. 4, make sure that the pushlock
button latches in place! To remove the battery
pack, proceed in reverse order.
Important!
Use only batteries which are charged to the same
level. Never combine full and half-full batteries.
Always charge the two batteries simultaneously.
The equipment‘s operating time depends on the
battery with the lower charge level. The two batte-
ries must always be fully charged before use.
5.3 Charging the battery (Fig. 5a)
1. Take the battery pack out of the equipment.
Do this by pressing the pushlock button.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(D) into the socket outlet. The green LED will
then begin to blink.
3. Insert the battery pack (E) into the charger
(D).
4. In section 11. „Charger indicator“ you will fi nd
a table with an explanation of the LED indica-
tor on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the power of the cordless leaf blower
drops. Never fully discharge the battery pack. This
will cause it to develop a defect.
5.4 Battery capacity indicator (Fig. 5b)
Press the button for the battery capacity indicator
(F). The battery capacity indicator (H) will indicate
the charge status of the battery by means of 3
LEDs.
Anl_PXCJBLS_0182U_SPK7.indb 10 Anl_PXCJBLS_0182U_SPK7.indb 10 26.08.2019 05:57:12 26.08.2019 05:57:12