manualshive.com logo in svg

Ozito PXBSPS-180, Инструкция по эксплуатации, Страница: 6 / 8

Поделиться
Скачать
Ozito PXBSPS-180 Скачать руководство пользователя страница 6

The polisher is not removing the compound from the 

surface

Ensure a clean polishing bonnet (not the foam application pad) is fitted to 

the polisher. 

Sparking visible through the housing air vents

A small amount of sparking may be visible through the housing vents. This 

is normal and does not indicate a problem.

Short Battery Runtime

Ensure the battery is properly charged. It will take 4-5 charging cycles 

before the battery reaches optimum charge and run time.

Digital Error Codes

If a problem occurs with the tool, an error code will show on the digital 

display screen. Refer to the table below for the error code meaning and 

possible solutions. 

If the tool still does not start after following the directions below, contact 

Ozito Customer Service.

6. USING THE SANDER

7. TROUBLESHOOTING

WARNING! 

THIS PRODUCT IS NOT RECOMMENDED 

FOR SANDING DRYWALL OR PLASTER DUE TO 
THE ULTRA-FINE SANDING PARTICLES PRODUCED. 
DRYWALL SANDERS IN CONJUNCTION WITH DUST 
EXTRACTION ARE RECOMMENDED FOR DRYWALL 
AND PLASTER SANDING APPLICATIONS.

Sanding Operations

1.  Secure the material to be sanded where possible.

2.  Fit the appropriate grit sandpaper to the accessory disc.

3.  With a firm grip on the sander, switch the tool on.

4.  Gradually lower the sander onto 

the workpiece with a slight 

forward movement.

5.  For optimum results, use either of these strokes.

Sanding Tips

Never force the sander. The weight of the sander supplies adequate 

pressure, allowing the sandpaper to do the work. Applying additional 

pressure will slow the motor, rapidly wear the sandpaper, and greatly 

reduce the sander speed. This will slow the removal rate and produce an 

inferior quality surface.

WARNING! 

EXCESSIVE PRESSURE WILL OVERLOAD 

THE MOTOR, CAUSING OVERHEATING AND 
POSSIBLE DAMAGE TO THE MOTOR AND/OR 
DAMAGE TO THE SURFACE.

 Be sure to check your workpiece often. The sander is capable of removing 

material rapidly, especially with coarse paper.

Do not sand on one spot for too long. The sander’s rapid action may remove 

too much material, creating an uneven surface.

BRUSHLESS

0

I

25

Forward/

Backwards

Side to Side

Error 

Code

Cause

Solution

E1

Battery Current 

Overload

Start the tool with no load on it. If the tool 

runs normally, you may be applying too much 

pressure while working. 
Change the attached battery. 

E3, E4 Tool is 

overloaded

Start the tool with no load on it. If the tool 

runs normally, you may be applying too much 

pressure while working. 

E5

Tool is 

overheated

Allow the tool to cool down for 30 minutes 

before restarting.

E6

Battery is out of 

charge

Change/charge the battery

E7, E8 Mechanical 

(Gear) failure

Start the tool with no load on it.
Change the battery.

E9

Battery voltage 

is too high

Change the battery & start the tool with no 

load on it.

Содержание PXBSPS-180









Отзывы:

Нет отзывов