ELECTRICAL SAFETY
WARNING!
When using mains-powered tools, basic safety precautions, including
the following, should always be followed to reduce risk of fire, electric shock, personal
injury and material damage.
Read the whole manual carefully and make sure you know how to switch the tool off in an
emergency, before operating the tool.
Save these instructions and other documents supplied with this tool for future reference.
The charger has been designed for 230V and 240V only. Always check that the power supply
corresponds to the voltage on the rating plate.
Note:
The supply of 230V and 240V on Ozito tools are interchangeable for Australia and New
Zealand.
This tools charger is double insulated; therefore no earth wire is required.
Note: Double insulation does not take the place of normal safety precautions when
operating this tool. The insulation system is for added protection against injury
resulting from a possible electrical insulation failure within the tool.
If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in
order to avoid a hazard.
Using an Extension Lead
Always use an approved extension lead suitable for the power input of this tool. Before use, inspect
the extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged
or defective.
When using an extension lead on a reel, always unwind the lead completely. Use of an extension
lead not suitable for the power input of the tool or which is damaged or defective may result in a
risk of fire and electric shock.
The power supply for this products charger should be protected by a residual current device (rated
at 30mA or less). A residual current device reduces the risk of electric shock.
GENERAL POWER TOOL SAFETY WARNINGS
WARNING!
Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference. The term “power tool” in
the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless)
power tool.
1. Work area safety
a.
Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust.
Power tools create sparks which may ignite the dust or fumes.
c.
Keep children and bystanders away while operating a power tool.
Distractions can cause you
to lose control.
2. Electrical safety
a.
Power tool plugs must match the outlet.
Never modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
b.
Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of electric shock if your body is earthed or grounded.
c.
Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase
the risk of electric shock.
d.
Do not abuse the cord.
Never use the cord for carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords
increase the risk of electric shock.
e.
When operating a power tool outdoors, use an extension cord suitable for outdoor use.
Use
of a cord suitable for outdoor use reduces the risk of electric shock.
3. Personal safety
a.
Stay alert, watch what you are doing and use common sense when operating a power
tool.
Do not use a power tool while you are tired or under the influence of drugs, alcohol or
medication. A moment of inattention while operating power tools may result in serious personal
injury.
b.
Use personal protective equipment
. Always wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c.
Prevent unintentional starting.
Ensure the switch is in the off-position before connecting to
power source and/or battery pack, picking up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools that have the switch on invites accidents.
d.
Remove any adjusting key or wrench before turning the power tool on
. A wrench or a key left
attached to a rotating part of the power tool may result in personal injury.
e.
Do not overreach.
Keep proper footing and balance at all times. This enables better control of
the power tool in unexpected situations.
f.
Dress properly.
Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
g.
If devices are provided for the connection of dust extraction and collection facilities, ensure
these are connected and properly used.
Use of dust collection can reduce dust-related
hazards.
h.
Do not let familiarity gained from frequent use of tools allow you to become complacent and
ignore tool safety principles.
A careless action can cause severe injury within a fraction of a
second.
4. Power tool use and care
a.
Do not force the power tool.
Use the correct power tool for your application. The correct
power tool will do the job better and safer at the rate for which it was designed.
b.
Do not use the power tool if the switch does not turn it on and off.
Any power tool that
cannot be controlled with the switch is dangerous and must be repaired.
c.
Disconnect the plug from the power source and/or the battery pack from the power
tool before making any adjustments, changing accessories, or storing power tools.
Such
preventive safety measures reduce the risk of starting the power tool accidentally.
d.
Store idle power tools out of the reach of children and do not allow persons unfamiliar with
the power tool or these instructions to operate the power tool.
Power tools are dangerous in
the hands of untrained users.
e.
Maintain power tools.
Check for misalignment or binding of moving parts, breakage of parts
and any other condition that may affect the power tool’s operation. If damaged, have the power
tool repaired before use. Many accidents are caused by poorly maintained power tools.
f.
Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g.
Use the power tool, accessories and tool bits etc. in accordance with these instructions,
taking into account the working conditions and the work to be performed.
Use of the power
tool for operations different from those intended could result in a hazardous situation.
h.
Keep handles and grasping surfaces dry, clean and free from oil and grease.
Slippery handles
and grasping surfaces do not allow for safe handling and control of the tool in unexpected
situations.
5) Battery tool use and care
a)
Recharge only with the charger specified by the manufacturer.
A charger that is suitable for
one type of battery pack may create a risk of fire when used with another battery pack.
b)
Use power tools only with specifically designated battery packs.
Use of any other battery
packs may create a risk of injury and fire.
c)
When battery pack is not in use, keep it away from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal objects, that can make a connection from
one terminal to another.
Shorting the battery terminals together may cause burns or a fire.
d) U
nder abusive conditions, liquid may be ejected from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help
.
Liquid ejected from the battery may cause irritation or burns.
e)
Do not use a battery pack or tool that is damaged or modified.
Damaged or modified
batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
f)
Do not expose a battery pack or tool to fire or excessive temperature.
Exposure to fire or
temperature above 130 °C may cause explosion.
g)
Follow all charging instructions and do not charge the battery pack or tool outside the
temperature range specified in the instructions.
Charging improperly or at temperatures
outside the specified range may damage the battery and increase the risk of fire.
6) Service
a)
Have your power tool serviced by a qualified repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is maintained.
b)
Never service damaged battery packs.
Service of battery packs should only be performed by
the manufacturer or authorized service provider.
PLANER SAFETY WARNINGS
WARNING!
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
•
Wait for the cutter to stop before setting the tool down.
An exposed cutter may engage the
surface leading to possible loss of control and serious injury.
•
Use clamps or another practical way to secure and support the workpiece to a stable
platform.
Holding the work by hand or against the body leaves it unstable and may lead to loss
of control.
•
Use of this tool can generate dust containing chemicals known to cause cancer, birth
defects or other reproductive harm.
Use appropriate respiratory protection.
•
Be sure to read the instruction manual thoroughly before using this tool.
•
Be sure to switch OFF immediately if the tool is jammed in work.
•
Be sure the tool is disconnected from power source when cleaning or making adjustments
to the tool.
•
Be sure the tool is properly held and set for correct use before turning switch to ON.
•
Be sure to use specified replacement parts only.
•
Be sure to maintain tool with care.
Follow instructions for lubricating and changing
accessories.
•
Be sure to store tool in a clean dry place after disconnecting from power source.
•
Keep air vents unobstructed for proper motor cooling.
•
DO NOT lay tool down on shoe when the blades are exposed.
This can chip the blades.
• Keep side dust extraction port unobstructed at all times.
•
Never reach under the tool for any reason unless it is turned off and the battery is
disconnected.
•
BLADES ARE EXPOSED AND EXTREMELY SHARP.
•
Use this tool for working with wood and wood products only.
•
Never operate without securely holding the front handle.
•
Always operate planer with two hands.
•
Planer blades are extremely sharp – Handle with great care.
•
Some wood contains preservatives such as copper chromium arsenate (CCA) which can be
toxic.
When sanding, drilling, or cutting these materials extra care should be taken to avoid
inhalation and minimise skin contact.
