HINTS & TIPS
• Do not force the saw into the cut. Apply only light pressure whilst running the
engine at full throttle.
• If the saw chain gets caught in the cut, do not try to remove it by twisting the
guide or pulling forcibly. Use a lever or wedge to open up the cut so that the
saw chain is freed.
• While cutting, always:
• Run the chainsaw motor at full revs. This makes the job safer, as there is
less chance of pull-in or kick-back.
• Position your body to the left of the chainsaw so if it kicks back
uncontrollably, it goes over your right shoulder, never stand in the cutting
line of the saw.
• Keep a firm grip with your left hand on the front handle, with your thumb
securely below the handle.
• The swivel of your wrist in a kick-back situation will activate the chain brake.
• Make sure the chain is tensioned correctly.
Adjusting the carburettor
The carburettor is factory set and should not require adjustment.
Changes in operating conditions may require fine tuning of the carburettor. A
special tool is required for making these adjustments.
Contact Ozito Customer Service for advice and instructions:
Aus: 1800 069 486
NZ: 0508 069 486
Replacing the spark plug
When the chainsaw will not start and everything has been checked, it is
likely the spark plug will need replacing. The spark plug is not covered under
warranty.
To replace the spark plug:
1. Unscrew and remove the filter cover knob.
2. Remove the filter cover.
3. Pull the spark plug lead off the spark plug end.
4. Loosen (anti-clockwise) the spark plug using the larger socket side of the
socket wrench provided.
5. Remove the spark plug and replace with a new one, as specified.
Spark plug types:
LD L8RTF, NGK BPMR7A, Champion RCJ7Y.
6. Secure the spark plug in position by tightening
(clockwise) the spark plug using the socket wrench
provided.
7. Fix the spark plug lead back to the end of the
spark plug ensuring it clicks into place.
8. Replace the filter cover (19) and secure in place
with the filler cover knob.
Adjusting the Automatic Oil Feed System
It is possible to adjust the flow rate of the chain bar oil if it is not supplying a
sufficient quantity of oil to the chain.
1. Turn the saw onto its side.
2. Using the screwdriver provided, adjust the oil
feed by rotating clockwise to decrease the flow of
oil, or rotating anti-clockwise to increase the flow of
oil.
3. Test the operation of the automatic oil feed
system to ensure sufficient oil is being supplied to
the chain. (Refer to the “Operation” section overleaf
for instructions on how to test automatic oil feed
system.)
0.6 - 0.7mm
Note:
The chainsaw warranty does not cover components that have been
subjected to operator abuse or negligence. To receive full value from the
warranty, the operator must maintain the chainsaw as instructed in this manual.
Ozito Industries will not be responsible for any damage or injuries
caused by repair of the tool by an unauthorised person or mishandling
or mistreatment of the tool. This tool is designed for Domestic Home Use
only. Use in commercial or industrial environments will void the warranty.
CARING FOR THE ENVIRONMENT
Petrol tools that are no longer usable should not be disposed
of with household waste but in an environmentally friendly way.
Please recycle where facilities exist. Check with yourlocal council
authority for recycling advice.
Recycling packaging reduces the need for landfill and raw
materials. Reuse of recycled material decreases pollution in the
environment. Please recycle packaging where facilities exist.
Check with your local council authority for recycling advice.
Chain
SPPCS406-094
Guide
Bar SPPCS406-095
Priming
Bulb
SPPCS406-74
Damper
SPPCS406-136
Spare parts can be ordered from the Special Orders Desk
at your local Bunnings Warehouse.
For further information, or any parts not listed here, visit
www.ozito.com.au or contact Ozito customer service
Australia 1800 069 486
New Zealand 0508 069 486
E-mail: [email protected]
SPARE PARTS
DESCRIPTION OF SYMBOLS
cc
Cubic Centimeters (the standard measure of displacement in Europe and Asia)
n
o
No load speed
/min
Revolutions or reciprocation per minute
dB
Decibel level
Electrical Emissions Conformity (EMC)
Read the manual prior to use
Wear safety boots
Wear safety gloves
Warning
Be aware of moving branches
Pull recoil starter to start motor
Do not use chainsaw when
only holding with one hand
Use both hands when using chainsaw
Use eye, ear, head and breathing
protection when operating the chainsaw
Fuel inlet
On/Off
(Position: next to throttle trigger)
Setting the On/Off switch to Off,
stops the engine immediately
Choke control
(Position: above priming bulb)
Chain brake released (hollow arrow) and activated (solid arrow)
(Position: right side of machine, on chain drive cover)
CHOKE Start position (when engine is cold)
RUN Run position
Chain oil inlet
H
High run adjustment screw
L
Low run adjustment screw
T
Idel adjustment screw (Position: left side of
machine close to pull start handle)
MAX
MIN
