Power tools that are no longer usable should not be disposed of
with household waste but in an environmentally friendly way. Please
recycle where facilities exist. Check with your local council authority for
recycling advice.
Recycling packaging reduces the need for landfill and raw materials.
Reuse of recycled material decreases pollution in the environment.
Please recycle packaging where facilities exist. Check with your local
council authority for recycling advice.
MAINTENANCE
DESCRIPTION OF SYMBOLS
CARING FOR THE ENVIRONMENT
TROUBLESHOOTING
1. When not in use, the detail sander should be stored in a dry,
frost free location, keep out of children’s reach.
2. Keep ventilation slots of the detail sander clean at all times and
prevent anything from entering.
3. If the housing of the detail sander requires cleaning, do not use
solvents. Use of a cloth only is recommended.
4. Blow out the ventilation slots with compressed air periodically .
Note:
Ozito Industries will not be responsible for any damage or
injuries caused by repair of the detail sander by an unauthorised
person or by mishandling.
Spare parts can be ordered from the Special Orders Desk
at your local Bunnings Warehouse.
For further information, or any parts not listed here, visit
www.ozito.com.au or contact Ozito Customer Service:
Australia 1800 069 486
New Zealand 0508 069 486
E-mail: [email protected]
SPARE PARTS
BATTERY AND CHARGER SAFETY WARNINGS
THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS FOR YOUR BATTERY
CHARGER.
1.
Before using the charger read all instructions and cautionary markings on the charger, battery pack and
the product using the battery pack.
1.
This charger is not intended for any uses other than charging rechargeable batteries. Any other use may
result in risk of fire, electric shock or electrocution.
2.
Do not place any object on top of the charger or place the charger on a soft surface that may result in
excessive internal heat. Place the charger in a position away from any heat source.
3.
To reduce risk of damage to the electric plug and cord, pull by the plug rather than the cord when discon-
necting the charger.
4.
Make sure the cord is located so that it will not be stepped on, tripped over, or otherwise subjected to
damage or stress.
5.
An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could
result in the risk of fire, electric shock or electrocution.
6.
Do not operate the charger if it has received a sharp blow, been dropped or otherwise damaged in any
way. Have it checked by an electrician or power tool repairer.
7.
Do not disassemble charger. Take it to an electrician or power tool repairer when service or repair is
required. Incorrect reassembly may result in a risk of electric shock, electrocution or fire.
8.
To reduce risk of electric shock, unplug the charger from the outlet before attempting any cleaning.
Removing the battery pack will not reduce this risk.
9.
Never attempt to connect 2 chargers together.
10.
DO NOT store or use the tool and battery pack in locations where the temperature may reach or exceed 40ºC
(such as inside sheds or metal buildings in summer).
11.
The charger is designed to operate on standard household electrical power (240 volts). Do not attempt to
use it on any other voltage!
12.
The battery pack is not fully charged out of the carton. First read the safety instructions and then follow
the charging notes and procedures.
13.
The longest life and best performance can be obtained if the battery pack is charged when the air tem-
perature is between 18 - 24ºC. Do not charge the battery pack in an air temperature below 10ºC or above
40ºC. This is important and will prevent damage to the battery pack.
14.
Do not incinerate the battery pack even if it is seriously damaged or is completely worn out. The battery can
explode in a fire.
15.
Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks or
cracks, immediately discontinue use and do not recharge.
16.
During charging, the battery must be placed in a well ventilated area.
Warning
Read instruction manual
ø
Diameter
mA
Milliamperes
Recycle battery
Do not put in the rubbish
Polarity
Do not incinerate
Do not get battery wet
Thermal cut-out protection
Transformer Energy
Rating (MEPS)
Double insulated
/min
Revolutions or reciprocation per minute
Ah
Amp hour
Indoor use only
Lithium Ion battery
Do not use or store battery in
temperatures exceeding 50ºC
Electrical Emissions
Conformity (EMC)
Nm
Newton Meters
n
o
No load speed
V
Volts
Hz
Hertz
ac/~
Alternating current
W
Watts
Direct current
dc/
18V Li-ion Battery Pack
SPCDL018-37
Charging
Stand
SPCDL018-38
Charging
Adaptor
SPCDL5010-34
LED lights do not illuminate on charger
Check the charging adaptor is securely plugged into the wall out let.
Check the battery is firmly connected to the charging cradle.
Check that the charging jack is securely connected to the charging cradle.
The battery has a short run time
Ensure the battery is properly charged. It will take 4-5 charging cycles
before the battery reaches optimum charge and run time. On the initial
charge, the battery requires 5 hours of charging. Subsequent charging
only requires 3-5 hours.
Sparking visible through the housing air vents
A small amount of sparking may be visible through the housing vents.
This is normal and does not indicate a problem.
Sandpaper Selection
Selecting the correct grit of sandpaper is an important step in achieving
optimum results. Coarse grit will remove the most material. Finer grit will
produce a smoother finish. The condition of the workpiece will determine the
grit of the sandpaper to be used. The higher the grit number, the finer the
grade of sandpaper.
If the surface is rough, start with a coarse grit and sand until the surface is uniform.
Medium grit may then be used to remove scratches left by the coarser grit. Finer
grit is then used to finish the surface. Always continue sanding with each grade of
sandpaper until the surface is uniform.
MATERIAL
APPROPRIATE GRIT
Coarse Sanding
Fine Sanding
Paintwork
180
400
Wood
: Softwood
60
240
Hardwood
60
180
Veneer
240
320
Note
: If intermediate sanding is required, choose a grit rating between coarse and
fine. The above table is intended as a guide only. To ensure a satisfactory result,
a small, inconspicuous area should first be tested to ensure the grit of sandpaper
chosen is suitable for the desired finish.