manualshive.com logo in svg

Oxford Instruments Andor Balor, Руководство по оборудованию, Страница: 45 / 72

Поделиться
Скачать
Oxford Instruments Andor Balor Скачать руководство пользователя страница 45

Version 1.0 rev 14 Aug 2019

45

Balor

4.9.8  R

olling

 s

HUtteR

 - 100% d

Uty

 c

ycle

 e

xteRnal

 e

xposURe

 t

RiggeRing

In this mode, every positive edge of the external trigger will initiate a frame read out and start a new exposure. The 
period of external trigger pulse defines exposure and cycle time for each frame read out. 

On detection of the first positive edge, a frame read out is initiated, this frame is discarded as it does not contain the 
correct exposure period. Reading out this first frame effectively begins the first exposure. When the next positive edge of 
the external trigger is detected, a signal frame read out phase begins, ending the first exposure and starting the next.

Figure 18: Rolling Shutter - 100% Duty Cycle - External Exposure.

Table 9: Rolling Shutter - 100% Duty Cycle External Exposure Triggering.

Parameter

Minimum 

Maximum

Exposure

1 Frame + 3 Row

3600 s

Cycle Time (EXT Trig Period)

Exposure

-

External Delay

1

2 Row

EXT Trig Pulse Width

2 Sensor Speed Clock Cycles

-

FIRE low period

1 Row

-

Содержание Andor Balor









































































Отзывы:

Нет отзывов