Oxbox J951X D Series Скачать руководство пользователя страница 16

Страница: 16 / 44

Before using

Table 4

, the number of pipes (1-pipe or 2-pipe)

connected to the furnace must be known. Find the proper

furnace style (upflow, horizontal, or downflow) and then the

side that the pipes will exit from the furnace. Finally select

the option that properly matches your installation type. For

. For J951X*D series, see

Figure 36 (page 39)

NOTE

: It is important that Direct Vent (2-pipe) systems

maintain an airtight flow path from the air inlet to the flue

gas outlet. The furnace ships from the factory with two holes

in the cabinet for the air inlet and flue gas outlet. In certain

configurations, it is necessary to remove and relocate a plastic

plug in the furnace cabinet. If changing the position of the air

inlet and flue gas outlet, it is required that the previous hole

be closed off with the plastic plug to maintain air tightness

in the furnace. The hole locations for all furnace series are

shown in

Figure 29

and

Figure 30

Inducer Assembly Rotation

WARNING:

Inducer rotation must be completed before

the furnace is connected to gas and electric. If

both utilities have been connected, follow the

shutdown procedures printed on the furnace

label and disconnect the electrical supply.

CAUTION:

It is good practice to label all wires prior to

disconnection. Wiring errors can cause improper

and dangerous operation.

1. Disconnect the electrical harness from the inducer

assembly.

2. Remove the inducer assembly ground wire from the blower

deck.

3. Remove 3 screws securing the inducer assembly to the

header box.

4. Rotate the inducer assembly to its new position.

5. Secure the inducer assembly to the header box by

reinstalling the three screws. If the inducer assembly is

rotated to the left or right side of the furnace, use the extra

screw provided in the parts package.

J951X*U & J951X*D SERIES - CONVENTIONAL (1 PIPE)

VENT

DIRECTION

UPFLOW

HORIZONTAL

RIGHT

HORIZONTAL

LEFT

DOWNFLOW

Right

N/A

N/A

Left

N/A

J951X*U & J951X*D SERIES - DIRECT VENT (2-PIPE)

VENT

DIRECTION

UPFLOW

HORIZONTAL

RIGHT

HORIZONTAL

LEFT

DOWNFLOW

Right

N/A

N/A

Left

N/A

Table 4. Vent & Inducer Blower Options

6. Remove the cabinet plug from side of furnace and reinstall

in hole on opposite side of cabinet.

7. Install in-line drain assembly and tubing.

8. Install all condensate drain lines. For J951X*U series,

see

Figure 34 (page 37)

Figure 35 (page 38)

. For

J951X*D series, see

Figure 36 (page 39)

9. Reconnect the electrical harness to the inducer assembly.

10. Reconnect the inducer assembly ground wire to the blower

deck or door.

11. Verify operation as detailed on the furnace label.

Pressure Switch Tubing

All upflow / horizontal furnaces have two switches, one

connected to the static tap on the inducer assembly and the

other to the collector box.

Figure 14

displays the proper routing

of pressure switch tubing for J951X*U furnaces. Downflow

(J951X*D) furnaces require only one switch connected to

the inducer’s static tap as shown in

Figure 15

Figure 14. Pressure Switch Tubing for

Upflow Furnaces

Models J951X038U, J951X054U, J951X072U,

J951X090U, J951X108U, & J951X120U

Figure 15. Pressure Switch Tubing for

Downflow Furnaces

Models J951X054D, J951X072D, & J951X090D

Содержание J951X D Series













































Результаты поиска

Содержание J951X D Series

Отзывы:

Похожие инструкции для J951X D Series

Бренды по названию

Популярные бренды

Oxbox J951X D Series, Руководство по установке

Результаты поиска

Содержание J951X D Series

Отзывы:

Похожие инструкции для J951X D Series

Бренды по названию

Популярные бренды