Oxbox J951X D Series Скачать руководство пользователя страница 40

Страница: 40 / 44

TROUBLESHOOTING

If the furnace fails to operate check the following:

• Is the thermostat operating properly?

• Are the blower compartment door(s) in place?

• Is the furnace disconnect closed?

• Has the circuit breaker tripped or the control board fuse

burned open?

• Is the gas turned on?

• Are any manual reset switches open?

• Is the filter dirty or plugged?

• Is the flame sensor coated? (Remove and clean with

steel wool.

(Do not use emery cloth or sandpaper!)

• Is there blockage in the condensate drain switch? Also

verify that there is no double trapping of condensate.

• Is the secondary heat exchanger free of debris and

clogs?

• Is evaporator coil clean and free of debris (If applicable).

• Are all the LED’s on the furnace control board constantly

ON? If not, refer to

Table 13

or the wiring diagram,

Figure

31 (page 30)

Figure 32 (page 31)

to determine fault

condition.

• Are all the LED’s on the motor control board constantly

ON? If not, refer to

Table 14

to determine fault condition.

IMPORTANT NOTE:

The furnace will lock out after 5 failed attempts for ignition

and will try again every hour if the call for heat remains.

• If the Inducer Blower is operating, and items above have

been verified, check the Blower Limit Switch and reset if

necessary. See

Figure 37 (page 41)

Figure 38 (page

41)

for component location.

• If the furnace operates when the Blower Limit Switch is

reset, contact a qualified service technician to identify

and repair the problem.

• If the furnace still doesn’t operate, check the Flame Roll-

out Switches and reset if necessary.

• If the furnace operates when the Flame Rollout Switch

is reset, contact a qualified service technician to identify

and repair the problem.

DIAGNOSTIC DESCRIPTION

GREEN LED

RED LED

Control Fault (No Power)

Off

L1/Neutral Polarity Fault

Flash

1 Hour Lockout

Alternating Flash

Normal Operation

Pressure Switch Closed Fault

Flash

Pressure Switch Open Fault

Flash

Open Limit Switch Fault

Flash

Off

DIAGNOSTIC DESCRIPTION

YELLOW LED

Low Flame Sensor Signal

Continuous Flash

Flame Present

Table 13. Control Board Fault Conditions

FURNACE COMPONENTS

The descriptions below are various functional components

that affect the operation and shutting down of this furnace.

Some of these components and their locations are shown

Figure 37 (page 41)

Figure 38 (page 41)

. If any

component of the furnace must be replaced, use only factory

authorized replacement parts specified in the Replacement

Parts List provided online.

Condensate Drain Switch:

The Condensate Drain Switch

will shut down the furnace if the condensate drain from the

Collector Pan becomes clogged.

Blower Limit Switch:

Prevents operation when blower is

not operational.

Flame Sensor:

Verifies when a flame has carried over from

the igniter to the opposite end burner. If no flame is detected,

the furnace will shut down within 4 seconds.

Flame Roll-Out Switch:

Verifies that the burner flames are

drawn into the heat exchanger tubes. If the burner flames are

not properly drawn into the heat exchanger, the flame roll-out

switch will close the gas valve and initiate the shutdown cycle.

Gas Valve:

Controls the flow of gas to the burners. When the

gas valve is energized it automatically opens and regulates

the gas pressure in the manifold.

Inducer Assembly:

Vents products of combustion to the

outside.

Pressure Switches:

Verifies that the inducer is drawing

the combustion gases through the heat exchanger. The

pressure switch prevents furnace operation with excessive

flue/condensate blockage or improper inducer operation.

Supply Air Limit Switch:

Prevents the air temperature

leaving the furnace from exceeding the maximum allowable

outlet air temperature.

DIAGNOSTIC DESCRIPTION

RED LED

GREEN LED

Control Fault (No Power)

Off

Normal Operation

Motor Fault

Flash

Twin Fault (No Motor Fault)

Flash

Communications Fault

Flash

Table 14. Motor Control Board Fault Conditions

Содержание J951X D Series













































Результаты поиска

Содержание J951X D Series

Отзывы:

Похожие инструкции для J951X D Series

Бренды по названию

Популярные бренды

Oxbox J951X D Series, Руководство по установке

Результаты поиска

Содержание J951X D Series

Отзывы:

Похожие инструкции для J951X D Series

Бренды по названию

Популярные бренды