Oxbox J951X D Series Скачать руководство пользователя страница 37

Страница: 37 / 44

Figure 34. Venting Options for Upflow Installations (J951X*U Series)

J951X*U SERIES UPFLOW - 1 PIPE OPTIONS

J951X*U SERIES UPFLOW - 2 PIPE OPTIONS

Plug

VIEW -B-

VIEW -A-

Plug

OPTION 1

See VIEW A for drain line positions

Rubber

Grommet

OPTION 2

See VIEW P for drain line positions

Rubber

Grommet

OPTION 3

See VIEW A for drain line positions

OPTION 4

See VIEW B for drain line positions

COMBUSTION

AIR

COMBUSTION

AIR

COMBUSTION AIR

FLUE PIPE

Plug

FLUE PIPE

Rubber

Grommet

Rubber

Grommet

PVC Tee

PVC Trap

PVC Tee

PVC Trap

PVC Tee

PVC Trap

PVC Tee

PVC Trap

See

NOTE 5

See

NOTE 5

Inline Drain Tube

(Factory Supplied)

See NOTE 4

Collector Box Drain

(Factory Equipped)

See NOTES 2 & 3

Inline Drain Tube

(Field Supplied)

See NOTE 3

Collector Box Drain

(Factory Equipped)

See NOTES 2 & 3

See

NOTE 5

See

NOTE 5

Field Supplied

Drain Line Attached

to PVC Trap

(Do Not Trap)

NOTES:

1. See Accessories section (

page 17

) for optional PVC Tee configurations and drainage options.

2. Drain lines must be trapped with a J-Trap or field supplied loop. Traps may be positioned inside or outside the cabinet. All drain

lines must be routed externally from the cabinet.

3. Inline drain is required only if “X” is greater than 6 feet.

4. Tubing needs to be cut to length and attached during unit installation.

5. Horizontal piping from inducer to flue pipe must be sloped 1/4” per foot to ensure drainage to PVC trapt.

Содержание J951X D Series













































Результаты поиска

Содержание J951X D Series

Отзывы:

Похожие инструкции для J951X D Series

Бренды по названию

Популярные бренды

Oxbox J951X D Series, Руководство по установке

Результаты поиска

Содержание J951X D Series

Отзывы:

Похожие инструкции для J951X D Series

Бренды по названию

Популярные бренды