Owon SDS1000 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 68

background image

4.Advanced User Guidebook

38

Copy the firmware file onto the root directory of your USB memory device.

3. Insert the USB memory device into the front-panel USB port on your

instrument.

4. Push the

Utility

button, select

Function

in the right menu, select

Update

in the

left menu.

5. In the right menu, select

Start

, the messages below will be shown.

6.

In the right menu, select

Start

again, the interfaces below will be displayed in

sequence. The update process will take up to three minutes. After completion,
the instrument will be shut down automatically.

7.

Press the

button to power on the instrument.

How to Measure Automatically

Push the

Measure

button to display the menu for the settings of the Automatic

Measurements. At most 8 types of measurements could be displayed on the
bottom left of the screen.

The  oscilloscopes  provide  39  parameters  for  auto  measurement,  including
Period,  Frequency,  Mean,  PK-PK,  RMS,  Max,  Min,  Top,  Base,  Amplitude,
Overshoot,  Preshoot,  Rise  Time,  Fall  Time,  +PulseWidth,  -PulseWidth,  +Duty
Cycle, -Duty Cycle, FRR, FRF, FFR, FFF, LRR, LRF, LFR, LFF,

Delay A→B ,

Delay A→B , Cycle RMS, Cursor RMS, Screen Duty, Phase A→B , Phase

«
...
41
42
43
44
45
...
»

Содержание SDS1000





































































Отзывы:

Нет отзывов

Похожие инструкции для SDS1000

Бренд: Qingdao H.Y Страницы: 6

Бренд: FENDT Страницы: 31

Бренд: NAD Страницы: 10

Бренд: Omlet Страницы: 2

Бренд: Omicron Страницы: 382

Бренд: Omicron Страницы: 188

Бренд: JBM Страницы: 12

Бренд: CAB Страницы: 30

Бренд: Xtricity Страницы: 4

IMPULSE 2 IT8026 Glute Master

Бренд: BM FITNESS Страницы: 18

Бренд: Joyolight Страницы: 4

SynCore RW Unit

Бренд: Ridder Страницы: 28

Бренд: Emos Страницы: 8

Бренд: Qtx Страницы: 6

Бренд: Hussmann Страницы: 20

Бренд: Waldbeck Страницы: 32

HydraMaster driMaster HiFlo Upholstery Tool

Бренд: U.S. Products Страницы: 28

Бренд: Bowa Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды