AirLive WL-5400CAM User’s Manual
48
Click “Start”, “Setting”, “Control Panel”, and the “Network” icon.
Select TCP/IP from the “Network” dialog box and from the “TCP/IP Properties” dialog box click “Specify an IP
address”.
If the
AirLive
WL-5400CAM Wireless Internet Camera is situated on a different subnet than your workstation,
you will not be able to set the IP address from this workstation. To verify make sure the first 3 sections of the IP
address of the
AirLive
WL-5400CAM Wireless Internet Camera corresponds to the first 3 sections of the
workstation. Therefore the IP address of the
AirLive
WL-5400CAM Wireless Internet Camera must be set from a
workstation on the same subnet.
A3:
Other possible problems might be due to the network cable. Try replacing your network cable. Test the
network interface of the product by connecting a local computer to the unit, utilizing a standard Crossover (hub to
hub) Cable. If the problem is not solved the
AirLive
WL-5400CAM Wireless Internet Camera might be faulty.
Q:
Why does the Power LED not light up constantly?
A:
The power supply used might be at fault. Confirm that you are using the provided power supply DC 5V for the
AirLive
WL-5400CAM Wireless Internet Camera and verify that the power supply is well connected.
Q:
Why does the Link LED not light up properly?
A1:
There might be a problem with the network cable. To confirm that the cables are working, PING the address
of a know device on the network. If the cabling is OK and your network is reachable, you should receive a reply
similar to the following (…bytes = 32 time = 2 ms).
A2:
The network device utilized by the
AirLive
WL-5400CAM Wireless Internet Camera is not functioning
properly such as hubs or switches. Confirm the power for the devices are well connected and functioning.
A3:
The wireless connection might be at fault. In ad-hoc mode make sure the
AirLive
WL-5400CAM Wireless
Internet Camera wireless channel and SSID is set to match the PC/Notebook wireless channel and SSID for direct
communication.
Under infrastructure mode make sure the SSID on the PC/Notebook and the
AirLive
WL-5400CAM Wireless
Internet Camera must match with the access point’s SSID.
Q:
Why does the
AirLive
WL-5400CAM Wireless Internet Camera work locally but not externally?
A1:
Might be caused from the firewall protection. Need to check the Internet firewall with your system
administrator.
A2:
The default router setting might be a possible reason. Need to double check if the configuration of the default
router settings is required.
Q:
Why does a series of broad vertical white line appears through out the image?
A:
A likely issue is that the CMOS sensor becomes overloaded when the light source is too bright such as direct
exposure to sunlight or halogen light. You need to reposition the
AirLive
WL-5400CAM Wireless Internet
Camera into a more shaded area immediately as this will damage the CMOS sensor.
Q:
There is bad focus on the
AirLive
WL-5400CAM Wireless Internet Camera, what should be done?
A1:
The focus might not be correctly adjusted for the line of sight. You need to adjust the
AirLive
WL-5400CAM
Wireless Internet Camera focus manually as described in Adjust Internet Camera Focus.
A2:
There is no adaptor fitted with your C-type lens. If you have previously changed the supplied CS-type lens,
you may have unintentionally installed a C-type lens without fitting the adaptor first.
Q:
Noisy images occur how can I solve the problem?
A1:
The video images might be noisy if the AirLive WL-5400CAM Wireless Internet Camera is used is a very low
light environment. To solve this issue you need more lighting.
A2:
There might be wireless transmission interference make sure there are no other wireless devices on the
network that will affect the wireless transmission.
