Outlaw 976 Скачать руководство пользователя страница 45

Страница: 45 / 47

Model 976 7.1 Channel Preamp/Processor

Specifi cations

Analog Section

AM Tuner Section

Input Impedance

47 KΩ

Output Impedance (Main-RCA)

<1 KΩ

Pre Out

4 V

Maximum Output

9 V

Volume Range (Main)

-90dB to +0dB (1dB resolution)

Frequency Response

10 Hz to 80 KHz ±1 dB

S/N Ratio (IHF-A)

-112 dB

Bass Management

Crossover Frequency Choices
(Small Speaker Setting)

40/50/60/70/80/90/100/110/
120/130/140/150H/200Hz

High-Pass (Satellite) Crossover Slope

12 dB/octave (2nd order)

Low-Pass (Subwoofer) Crossover Slope

24 dB/octave (4th order)

Tone Controls

Bass Center Frequency/Range

100 Hz ±10 dB

Treble Center Frequency/Range

10 KHz ±10 dB

FM Tuner Section

Sensitivity

IHF

10 dBu typ.

50dB S/N

13 dBu typ.

S/N Ratio

Mono

70 dB

Stereo

67 dB

Distortion

Mono

0.2%

Stereo

0.3%

Stereo Separation

40 dB typ.

Adjacent Channel Selectivity

70 dB ±400 KHz

IF Rejection Ratio

120 dB

Frequency Response

20 Hz to 15 KHz ±1.5 dB

Sensitivity (20dB S/N)

300 uV

S/N -45

Selectivity

25 dB

Distortion 0.7%

S/PDIF Coax Impedance

75 Ω

S/PDIF Coax Signal Strength

0.5Vp-p

Digital Signal Processor

TI-DA808

Digital Audio

General

Supply Voltage

120V, 60Hz only

Standby Power Consumption (Power Off )

0.5 W

Trigger Output Sequential Delay

50 mA @ 12 VDC

Dimensions (H/W/D)

4.625 x 17 x 11 in
117.5 x 431.8 x 279.4 mm

Weight

12.0 lb
5.44 kg

Содержание 976
















































Результаты поиска

Содержание 976

Отзывы:

Бренды по названию

Популярные бренды

Outlaw 976, Руководство пользователя

Результаты поиска

Содержание 976

Отзывы:

Бренды по названию

Популярные бренды