background image

14

CHARACTERISTICS AND SPECIFICATIONS

A. Construction and characteristics

• 

Transportable terrace/garden heater with tank housing

• 

Casing in steel with powder-coating or stainless steel

• 

Gas hose connections with metal clamp (screw caps for Germany)

• 

Heat emission from reflector

B. Technical Specifications

• 

Use propane, butane or their mixtures gas only.

• 

Max. wattage: 13000 watts

• 

Min. wattage: 5000 watts

• 

Consumption:

• 

Using the proper regulator according to outlet pressure of regulator as showed 

in the table above.

C. Table of injector

• 

The hose and regulator assembly must conform to local standard codes.

• 

Regulator outlet pressure should meet the corresponding gas category in the 

table of injector.

• 

The appliance requires approved hose in 1.4m length.

• 

• 

• 

The regulator must comply with the requirements of EN 16129:2013.

The hose must comply with the requirements of EN 16436-1:2014.

Read the intructions before installation and use.

Keep the instructions for future reference.

APPLIANCE CATEGORY:
TYPES OF GAS:

Butane                Propane

GAS PRESSURE:

28-30mbar          37 mbar        30 mbar                50mbar                 37mbar

30mbar               37 mbar        30 mbar                50mbar                 37mbar

Butane, propane 

or their mixtures

Butane, propane 

or their mixtures

Butane, propane 

or their mixtures

OUTLET PRESSURE 

OF REGULATOR:

3+(28-30/37)

3B/P(30)

I

3B/P(50)

I

3B/P(37)

I

I

APPLIANCE CATEGORY:
TYPES OF GAS:

Butane                Propane

GAS PRESSURE:

28-30mbar          37 mbar        30 mbar                50mbar                 37mbar

TOTAL HEAT

INPUT (Hs): (Qn)

13kW

INJECTOR SIZE:

The marking  for example  1.85 on the injector indicates that the size of injector is 1.85mm

1.85 mm for main burner
0.18 mm for pilot burner

1.45 mm for main burner
0.18 mm for pilot burner

1.65 mm for main burner
0.18 mm for pilot burner

Butane, propane 

or their mixtures

Butane, propane 

or their mixtures

Butane, propane 

or their mixtures

3B/P(30)

I

3B/P(50)

I

3B/P(37)

I

3+(28-30/37)

I

946g/h

929g/h

946g/h

GAS CONSUMPTION:

COUNTRY OF 
DESTINATION: 

GB,IE

Содержание OUT370609/PH100T

















Отзывы: