background image

10 

CAUTION

PLEASE READ CAREFULLY THE FOLLOWING SAFETY GUIDELINES BEFORE 

OPERATION.

• 

Do not use the patio heater for indoors, as it may cause personal injury or 

property    damage.

• 

This outdoor heater is not intended to be installed on recreational vehicles and/or 

boats.

• 

Installation and repair should be done by a qualified service person.

• 

Improper installation, adjustment, alteration can cause personal injury or 

property damage.

• 

Do not attempt to alter the unit in any manner.

• 

Never replace or substitute the regulator with any regulator other than the 

factory-suggested replacement.

• 

Do not store or use gasoline or other flammable vapors or liquids in the heater 

unit.

• 

The whole gas system, hose, regulator, pilot or burner should be inspected for 

leaks or damage before use, and at least annually by a qualified service person.

• 

All leak tests should be done with a soap solution. Never use an open flame to 

check for leaks.

• 

Do not use the heater until all connections have been leak tested.

• 

Turn off the gas valve immediately if smell of gas is detected. Turn Cylinder Valve 

OFF. If leak is at Hose/Regulator connection: tighten connection and perform 

another leak test. If bubbles continue appearing should be returned to hose’s 

place of purchase. If leak is at Regulator/Cylinder Valve connection: disconnect, 

reconnect, and perform another leak check. If you continue to see bubbles after 

several attempts, cylinder valve is defective and should be returned to cylinder’s 

place of purchase.

• 

Do not transport heater while it’s operating.

• 

Do not move the heater after it has been turned off until the temperature has 

cooled down.

• 

Keep the ventilation opening of the cylinder enclosure free and clear of debris.

• 

Do not paint the radiant screen, control panel or top canopy reflector.

• 

Control compartment, burner and circulation air passageways of the heater must 

be kept clean. Frequent cleaning may be required as necessary.

• 

The LP tank should be turned off when the heater is not in use.

• 

Check the heater immediately if any of the following occurs:

- The heater does not reach temperature.

- The burner makes popping noise during use (a slight noise is normal when the 

burner is extinguished).

- Smell of gas in conjunction with extreme yellow tipping of the burner flames.

• 

The LP regulator/hose assembly must be located out of pathways where people 

may trip over it or in area where the hose will not be subject to accidental damage.

• 

Any guard or other protective device removed for servicing the heater must be 

replaced before operating the heater.

Содержание OUT370609/PH100T

















Отзывы: