OTC DTX-202 TIG Скачать руководство пользователя

Страница: 62 / 80

Optional

DTX-2200-3000 AC/DC

15 Optional

The remote controls can be only used in the 2-STROKE and 4-STROKE welding modes.

15.1 MANUAL REMOTE CONTROL

WARNING: When using the machine for TIG welding it is OBLIGATORY to use the kit for simultaneously use.

Weld current can be measured at a distance by connecting up this control. The display will show the previous

maximum weld current value set on the welder. The remote control will adjust welding current from the minimum

to this value (for further information see Chapter 14.3). Just turn the adjustment knob on the welder to change

the maximum output value.

15.2 FOOT SWITCH

The foot switch replaces the torch button and the welding current setting knob. The display will show the

previous maximum weld current value set on the welder. The pedal will adjust the welding current from the

minimum to this value (for further information see chapter 14.3). Just turn the adjustment knob on the welder to

change the maximum output value.

NOTE:

• To use the pedal control correctly, set the “welding mode” to 2-STROKE and then the welding parameters

SLOPE UP time to 0 sec., SLOPE DOWN time to 0 sec.

• When using the machine for TIG welding the operator can use the torch button to start the weld and the pedal

to regulate the welding current remotely.

15.3 AIR AND/OR WATER-COOLED TORCH UP/DOWN

The up/down torch replaces the current setting knob on the front of the welder. Press right (+) and left (-) button

to adjust the active parameter. With this kind of torch, it is also possible to scroll the saved programs by pressing

the two (+) and (-) buttons.

Turn the knob to scroll the programs until an empty and unused program is found.

NOTE: The value shown on the display during welding represents the effective current output with all types of

control.

The digital control unit of the generator is fitted with a control recognition device which allows it to identify which

device is connected and take action accordingly. To allow the command recognition device to work correctly,

connect (with the machine switched off) the required accessory to the relative connector and then switch on the

welding machine with the on/off switch.

NOTE: It is not possible to memorize or open programs when the remote controls are connected (except for the

torch with UP/DOWN commands).

Содержание DTX-202 TIG

















































































Результаты поиска

Содержание DTX-202 TIG

Отзывы:

Похожие инструкции для DTX-202 TIG

Бренды по названию

Популярные бренды

OTC DTX-202 TIG, Руководство пользователя

Результаты поиска

Содержание DTX-202 TIG

Отзывы:

Похожие инструкции для DTX-202 TIG

Бренды по названию

Популярные бренды