Clean your electric kettle before first use
1. Wash the inside of the kettle and lid with mild detergent and water.
Rinse each thoroughly. Do not immerse the kettle or power base in
water or any other liquid. These items are not dishwasher safe.
2. Press the Lid Release Button (
) to open the lid. Fill the electric
kettle with fresh water to the “MAX” water level mark.
3. Plug power base into power outlet. Place kettle onto power base.
Follow the following section of “Boil Water at 100°C” to boil water.
4. When the water and unit have cooled, discard the water. Rinse with
cold water and repeat.
5. Your electric kettle is now ready for use.
Using Your Electric Kettle
1. Position the power base on a flat, heat resistant surface, as close as
possible to a power outlet.
2. Follow cord routing in power base according to exit patterns. Proper
cord routing will result in the power base laying flat when kettle is
placed in base. DO not operate kettle if power base is not flat. If
power base is not flat, remove kettle from power base and repeat
cord placement instructions.
3. To fill with water, press the Lid Release Button (
) to open the lid.
Fill the electric kettle with water to the desired level.
NOTE: Do not exceed the “MAX” water level mark indicated on
the electric kettle.
4. Plug the electric cord into an electric outlet, the kettle will beep and
all button lights will flash in BLUE once and then go off. The power
light ring will keep flashing in RED to indicate that the kettle is in
standby mode.
Boil Water at 100°C
1. Press Power Button ( ) at standby mode, the kettle will beep once.
The power light ring will illuminate in RED. The 100°C button will
flash in BLUE for 3 seconds and then remain illuminated until the
boiling process completes.
2. Once the water temperature reaches 100°C, the kettle will beep 5
times, and the 100°C button light will go off to indicate that the
water boiling is completed and the kettle will return to standby
mode automatically.
NOTE: Lid should always be firmly closed during boiling process.
3. Carefully lift the kettle from the power base and pour the hot water.
5
Nettoyage avant la toute première utilisation
1. Lavez l’intérieur de la verseuse et du couvercle avec un détergent
doux et de l’eau. Rincez-les à fond. Ne plongez pas la verseuse ou le
socle chauffant dans l’eau ou dans tout autre liquide. Ils ne sont pas
lavables au lave-vaisselle.
2. Ouvrez le couvercle en pressant sa touche de déblocage (
) puis
remplissez la verseuse d’eau fraîche, au plus jusqu’au repère «MAX
».
3. Branchez le socle chauffant, posez la verseuse sur le socle et agissez
tel qu’indiqué sous «Eau bouillie à 100 °C
» pour bouillir l’eau.
4. Quand l’eau et la bouilloire ont refroidi, videz l’eau. Rincez
l’intérieur de la verseuse à l’eau froide et répétez l’opération.
5. V
otre bouilloire électrique est alors prête à l’emploi.
Mode d’emploi de la bouilloire électrique
1. Posez le socle chauffant sur une surface plane et insensible à la
chaleur, aussi près que possible d’une prise de courant.
2. V
oyez où se trouvent les points de sortie du cordon que présente
le socle. Lorsque le cordon est acheminé comme il se doit, le socle
chauffant est absolument plat quand vous y placez la verseuse. Ne
faites PAS fonctionner la bouilloire si le socle chauffant n’est pas
d’aplomb mais retirez la verseuse et réacheminez le cordon.
3. Ouvrez le couvercle en pressant sa touche de déblocage (
) pour
remplir la verseuse d’eau jusqu’au niveau voulu.
REMARQUE: ne dépassez pas le repère «
MAX» qui est indiqué sur
la bouilloire électrique.
4. Branchez le cordon d’alimentation sur la prise de courant, la
bouilloire bipera et tous les voyants BLEUS clignoteront une fois
avant de s’éteindre. La bague lumineuse ROUGE de l’interrupteur
clignotera sans arrêt, indiquant que la bouilloire est en mode attente.
Eau bouillie à 100 °C
1. À partir du mode attente, pressez l’interrupteur (
) et la bouilloire
bipera une fois. La bague lumineuse de l’interrupteur luira ROUGE.
Le voyant BLEU de la touche 100 °C scintillera pendant 3 secondes
puis luira jusqu’à l’ébullition.
2. Quand la température de l’eau atteint 100 °C, la bouilloire émettra
5 bips et le voyant de la touche 100 °C s’éteindra, signe que l’eau a
bouilli. La bouilloire électrique reviendra alors automatiquement au
mode attente.
5