OSO Ecoline Geo RI HP, Руководство по установке

Страница: 3 / 16

- 3 -
1. To obtain the best performance from your OSO unvented system it is advisable to feed the unit
with an uninterrupted supply.
2. Before connecting to the multibloc, flush the cold supply pipework of all flux and debris.
3. Locate the water heater in a suitable position to facilitate the installation of the cold water supply,
discharge fittings and pipework. Also take into account access to the immersion heaters and the
commissioning valve.
4. Fit both 1/2’’ male heat pump sensor pockets to the Sensor Pocket bosses (12&21).
10. Remove the appropriate nuts and rings and connect the flexible hose to the expansion relief valve
and the right pointing T-piece connection.
11. If a balanced mains pressure cold water supply is required to a shower or bidet (over rim type
only), remove the blanking cap from the pressure reducing valve (3) and connect to the shower
or bidet cold supply. Do not use the balanced cold connection to feed bath taps as this can reduce
the flow available to the unvented cylinder.
12. Connect the cold supply to the Multibloc (3).
13. Fit the expansion vessel to the wall close to the water heater using the enclosed mounting bracket.
Connect the expansion vessel hose to the T piece in the cold feed pipe to the cylinder.
The expansion vessel is supplied with the OSO unit, fit as shown on page 2.
Hot water supply
14. Connect the hot water supply pipe to the outlet (9). Ensure connection is water tight.
Secondary return (optional)
15. Connect secondary return (if required) by fitting a T-piece (not supplied) into the cold feed tube (8)
according to diagram on page 16.
Discharge pipe
16. Connect the discharge pipe from the tundish (6). This must have a continuous fall and be fitted
in accordance with The Building Regulations (see page 16). The tundish should be installed away
from electrical devices.
Primary flow & return & motorised valve - heat pump
17. The heat pump primary flow and return connections should be made to the unit. The motorised valve
must be fitted either on the flow or return of the primary water heating circuit. The primary flow and
return connections are ¾” female. The valve has 22mm copper connections. The direction of the
primary flow in the coil is top to bottom.
200 litre cylinder:
5. Fit the combined male elbow drain cock to
cold supply point (13), so that the compress-
ion fitting is horizontal point to the right.
6. Fit the length of copper tube 22mm specified
in table 2 to the cold feed elbow with a right
angle bend as shown to include a T piece for
the expansion vessel.
7. Fit the pressure reducing valve to the top of
the copper tube so that the black knob is
facing right.
8. Fit a 15mm copper tube to the T & P valve
and bend around the top of the cylinder to
pass close and 50 mm to the left of the cold
feed pipe. Cut the pipe off 700 mm from the
floor. Fit the compression end of the T piece
to the bottom of the 15mm copper pipe with
the female end pointing down and the right
angle connection pointing 45° to the right.
9. Remove the nut and ring from the top
connection of the tundish and screw the male
thread into the female thread of the T piece.
250 & 300 litre cylinder:
5. Fit the combined male elbow drain cock to
cold supply point (13), so that the compress-
ion fitting is vertical.
6. Fit the length of copper tube 22mm specified
in Table 2 to the cold feed elbow (see 5
above) to include a T piece for the expansion
vessel.
7. Fit the pressure reducing valve to the top of
the copper tube so that the black knob is
facing right.
8. Fit the female outlet of the tee piece to the
temperature and pressure relief valve (5) with
the horizontal connection facing right at
approx. 45°.
9. Fit the tundish to the T piece using a short
length of copper tube.
COLD WATER SUPPLY