background image

Components supplied with the unit for site fitting

  (See also page 2 for component list)
* Multibloc valve, includes pressure reducing valve, line strainer, balanced cold water take off,

  (for shower or bidet only)

 check and expansion valve.

* Tundish
* 1/2’’F x 15 x 15 tee piece
* Flexible hose - 220 mm
* 1’’ x 22mm Elbow / Drain Cock
* 2 sensor pockets
* Motorised valve
* Expansion vessel.

Components factory fitted

* Immersion heater
* Thermostats / thermal cut-out
* Temperature and pressure relief valve.

Installation details

The OSO unvented unit is designed for use with supply pressure up to 10 bar. For pressures 

over 10 bar an additional pressure reducing valve must be fitted in the supply pipe to the unit.

PRODUCT REF. 

 

200 

250 

300

HEIGHT 

  1150  1400 1600

DIAMETER 

  580  580 580

WEIGHT EMPTY 

 

50 

55 

65

MAX WEIGHT FULL 

 

241 

292 

341

142039-01  GEO 11-2013

The Ecoline GEO is an indirect unvented cylinder designed and approved for use 

with  a  heat  pump.  The  heating  coil  has  been  specifically  designed  for  this  heat 

source, information is included in this manual to link the cylinder with the heat pump. 

This cylinder is manufactured and approved in accordance with EN 12897:2006.

This manual gives detailed advice for installation and should be read carefully prior 

to fitting any unvented unit. Where components are supplied only for indirect units, 

this is clearly shown. 

This OSO cylinder must be installed by a competent person and be installed in 

compliance with the OSO Installation and Maintenance Instructions, all current leg-

islation, codes of practice and regulations governing the installation of unvented hot 

water cylinders in force at the date of installation.

Health and Safety

Manual Handling Operations Regulations 1992 defines 

manual handling as: “any transporting or supporting of a 

load (including the lifting, putting down, pushing, pulling, 

carrying or moving thereof) by hand or bodily force”. The 

Regulations set no specific requirements such as weight 

limits. However common sense still has to be used 

based on an ergonomic approach for each individual.

DIMENSIONS AND WEIGHTS TABLE 1

PLEASE LEAVE THIS MANUAL WITH THE 

OSO

 UNIT AFTER INSTALLATION

INSTALLATION MANUAL

Ecoline Geo RI HP

Содержание Ecoline Geo RI HP

















Отзывы: