Osburn STRATFORD II OB04007 Скачать руководство пользователя страница 34

Страница: 34 / 72

Page 34

Installation and Operation Manual - Stratford II

ENGLISH

8.5.3 Framing with forced air distribution kit

If a finishing material is installed inside the enclosure, its thickness must be added to the following
measurements.

: Forced air duct

(Duct can be installed on the left [recommended]

on the right).

: Distance between framing and side fireplace standoff 18" (457 mm)

: Framing width (Installation with centered fireplace) 72

" (1848 mm)

8.5.4 Framing with corner installation

50 1/4"

1275mm

50 1/4"

1275mm

79 3/4"

2026mm

14 3/8"

365mm

14 3/8"

365mm

Framing configuration should be used as a reference only.

If a finishing material is installed inside the enclosure, its thickness must be added to the following
measurements.

Theses values are minimum measurements and may need to be increased to allow the installation
of the fresh air intake, the forced air distribution or the type of finishing material used.

Framing dimensions are for reference only. These measurements are recommended to prevent the ducts from being inside the standoff or have

too tight duct curves. Smaller dimensions can be used depending on the size and type of duct as well as the configuration of the installation.

HVAC duct, as per ULC S110 or UL 181, class 0 or class 1, must withstand temperatures up to 250oF.

Содержание STRATFORD II OB04007









































































Результаты поиска

Содержание STRATFORD II OB04007

Отзывы:

Похожие инструкции для STRATFORD II OB04007

Бренды по названию

Популярные бренды

Osburn STRATFORD II OB04007, Инструкция по установке и эксплуатации

Результаты поиска

Содержание STRATFORD II OB04007

Отзывы:

Похожие инструкции для STRATFORD II OB04007

Бренды по названию

Популярные бренды