background image

Page 14

Installation and Operation Manual - Stratford II

ENGLISH

The success of zone heating will depend on several factors, including the correct sizing and 
location of the fireplace, the size, layout and age of your home and your climate zone. Three-
season vacation homes can usually be heated with smaller fireplaces than houses that are 
heated all winter.

2.6  Emissions and Efficiency

The low smoke emissions produced by the special features inside this fireplace firebox mean 
that the household will release up to 90% less smoke into the outside environment than if an 
older conventional fireplace was used. But there is more to the emission control technologies 
than protecting the environment. 

The smoke released from wood when it is heated contains about half of the energy content 
of the fuel. By burning the wood completely, this fireplace releases all the heat energy from 
the wood instead of wasting it as smoke up the chimney. Also, the features inside the firebox 
allow control of the air supply meaning controlling the heat output, while maintaining clean and 
efficient flaming combustion, which boosts the efficient delivery of heat to the home.

The emission control and advanced combustion features of this fireplace can only work properly 
if the fuel used is in the correct moisture content range of 15% to 20%. Refer to the following 
section of suggestions on preparing fuelwood and judging its moisture. 

3.  Fuel

Good firewood has been cut to the correct length for the fireplace, split to a range of sizes and 
stacked in the open until its moisture content is down to 15% to 20%.

DO NOT BURN:

• 

GARBAGE;

• 

LAWN CLIPPINGS OR YARD WASTE;

• 

MATERIALS CONTAINING RUBBER, 
INCLUDING TIRES;

• 

MATERIALS CONTAINING PLASTIC;

• 

WASTE PETROLEUM PRODUCTS, PAINTS 
OR PAINT THINNERS, OR ASPHALT 
PRODUCTS;

• 

MATERIALS CONTAINING ASBESTOS;

• 

CONSTRUCTION OR DEMOLITION DEBRIS;

• 

RAILROAD TIES OR PRESSURE-TREATED 
WOOD;

• 

MANURE OR ANIMAL REMAINS;

• 

SALT WATER DRIFTWOOD OR OTHER 
PREVIOUSLY SALT WATER SATURATED 
MATERIALS;

• 

UNSEASONED WOOD; OR

• 

PAPER PRODUCTS, CARDBOARD, 
PLYWOOD, OR PARTICLE BOARD. THE 
PROHIBITION AGAINST BURNING THESE 
MATERIALS DOES NOT PROHIBIT THE 
USE OF FIRE STARTERS MADE FROM 
PAPER, CARDBOARD, SAW DUST, WAX 
AND SIMILAR SUBSTANCES FOR THE 
PURPOSE OF STARTING A FIRE IN AN 
AFFECTED WOOD HEATER.

BURNING THESE MATERIALS MAY RESULT IN THE RELEASE OF TOXIC FUMES OR 
RENDER THE HEATER INEFFECTIVE AND CAUSE SMOKE.

3.1  Tree Species

The tree species the firewood is produced from is less important than its moisture content. The 
main difference in firewood from various tree species is the density of the wood. Hardwoods are 
denser than softwoods.

Содержание STRATFORD II OB04007









































































Отзывы: