Osburn STRATFORD II OB04007 Скачать руководство пользователя страница 58

Страница: 58 / 72

Page 58

Installation and Operation Manual - Stratford II

ENGLISH

Installation rules and advice

• Do not connect the hot air ducts to a central heating system. The malfunction of the heating system

would overheat the fireplace.

• Do not use insulated flexible ducts as they may overheat.

• Do not use «T» fittings or anything other than those listed below.

• The hot air outlets can be installed in the same room as the fireplace or it can be installed in a room

upstairs.

• When forced air kit is installed in conjunction with a gravity kit, the forced air device will draw some

of the air from the gravity kit ducting, therefore reducing its efficiency.

Clearances

• There shall be a clearance of at least 12" (305 mm) between the hot air outlet frame and a ceiling,

side wall or mantle made of flammable material.

• When the duct passes through a wall or floor made of flammable material, a firestop radiation shield

(same as the one used for a class A chimney) must be installed in the opening of the wall or floor.
There must be a clearance of at least 2" (50 mm) between the ducts and the firestop.

12" MIN.

MIN.

13" X 13"

330mm X 330mm

Содержание STRATFORD II OB04007









































































Результаты поиска

Содержание STRATFORD II OB04007

Отзывы:

Похожие инструкции для STRATFORD II OB04007

Бренды по названию

Популярные бренды

Osburn STRATFORD II OB04007, Инструкция по установке и эксплуатации

Результаты поиска

Содержание STRATFORD II OB04007

Отзывы:

Похожие инструкции для STRATFORD II OB04007

Бренды по названию

Популярные бренды