7
5 : EG IN (Egress Input for N.O. Button)
A Normally Open (N.O.) input terminal referring to (-) ground for connecting N.O. button to activate
the output contact for door lock strike. Egress button is usually put inside the house near the door
for “request to exit”. More than one egress buttons can be connected in parallel to this terminal for
user convenience at other location(s), such as near the reception desk. Leave this terminal open if
not used.
6 : Data I/O Port
A data communication port prepared for the optional reader AR-2802 connection to expand the
access control system with two or more readers. The enrolled EM cards in the AR-2808 are also
accepted by the optional readers.
7 - 8 : Door Bell (Relay Contact for Optional Door Chime)
A Normally Open (N.O.) relay dry contact with maximum rating of 1Amp/24VDC controlled by the
BELL button, it is prepared to trigger an optional low voltage door chime. The contact point keeps
close as long as the bell button is pressed.
9 - 10 : Tamper Switch (Tamper Switch with N.C. Contact)
A Normally Closed (N.C.) dry contact while the reader is fixed on its back cover. The contact is open
while the reader is separated from its back cover. Connect this N.C. terminal to the 24 hour
protection zone of an alarm system if necessary in order to get alert from sabotage.
18
IV) SET SYSTEM SAFETY
LOCK-UP
III) SET OUTPUT MODE FOR DOOR LOCK
Auto - Confirm
Option 1 - 3
Auto - Confirm
Mode 2 - T
iming
Stop T
ime Counting
Start T
ime Counting
Auto - Confirm
Mode 1 - Start / Stop
FEA
TURE SETTING PROCEDURES SUMMAR
Y CHART
II) DELETE USER CARDS
I) RECORD USER CARDS
ENTER PROGRAMMING MODE & FEA
TURE GROUP
SELECTION
WITH MASTER CARD
SELECTION & EXECUTION
FUNCTION SELECTION WITH BELL
BUTT
ON
EXIT
PROGRAMMING MODE
Auto-Confirm
Feature Group 4 Selected
Auto-Confirm
Feature Group 3 Selected
Auto-Confirm
Feature Group 2 Selected
Read Master Card
4 TIMES
Status LED
ON ► Flashing
Read Master Card
3 TIMES
Status LED
ON ► Flashing
Read Master Card
2 TIMES
Status LED
ON ► Flashing
Auto-Confirm
Feature Group 1 Selected
Read Master Card
1 TIME
Status LED
ON ► Flashing
LED 4 - ON
LED 1, 2 & 3
Flashing
LED 3 - ON
LED 1 & 2 Flashing
LED 2 - ON
LED 1, 2 & 3
Flashing
LED 1 - ON
All 5 LEDs Flashing
Group LED
ON -- V
acancy
Available
Flashing -- Full
Auto - Confirm
Deletion Mode 3
Auto - Confirm
Deletion Mode 2
Auto - Confirm
Auto - Confirm
Deletion Mode 1
Storage Group 1-5
The Selected
LED - ON
Flashing
LED 2 -- ON
Flashing
LED 1 -- ON
Flashing
LED 3 -- ON
5 LEDs Flashing
LED 2 -- ON
2 Beeps
LED 1 -- ON
2 Beeps
Status LED ON
System Back
to
Normal operation
Read Master Card
1 TIME
Select The Group 1-5
For Cleaning
Read The Card of The
Lost Card F
ollows
Execution with Bell Button
Auto - Confirm
Read Un-used Cards
Read New User Cards
LED Jumper
ON & Stop at Desired
Time
The Selected Group LED - ON
Flashing During Cleaning
The Group LED of the Deleted Card ON for 1 Second / card
Group LED ON for 1 Second / Card
To “ Exit Programming Mode ” Directly
To “ Exit Programming Mode ” Directly
