12
C) Deletion Mode 3 – Delete one group of user cards (Group clearing):
2) Press BELL button to select deletion mode 3.
....
Response
: LED 3 is ON. After 2 seconds, the system confirms the selection with 2 beeps and
.........................
then the 5 LEDs flashing for five storage groups available.
3) Press BELL button to select the storage group 1-5 for group clearing.
....
Response
: The selected LED is ON. After 2 seconds, the system confirms the selection with 2
.........................
beeps.
4) Press BELL button again to execute group clearing.
....
Response
: The group LED flashes during clearing and 2 Beeps confirm clearing done.
....
Note:
Repeat procedure (3) & (4) for clearing of other storage groups if required.
5) Read Master Card 1 Time to exit Programming Mode.
....
Response
: 2 Beeps confirm reader back to normal operation.
Remark
:
After Group Clearing, it is necessary to re-store all the existing (not lost) User Cards back to the
Storage Group one by one with the procedures stated in the “
Record User Cards – The Feature
Group 1
” section.
Exit
Programming Mode
Group Clearing
Execution
4
Select Group 1-5
for Clearing
Select
Deletion Mode 3
Read Master Card 2 Times
Set System in Feature Group 2
5
3
2
1
4) Read Master Card 1 Time to close Programming Mode.
IIII
Response
:
2 Beeps confirm reader back to normal operation.
IIII
Note
:
IIII
There is a slot left at the memory stack after a card is deleted. In programming, the new cards will
IIII
fill in the slots first according to their position in the queue of the memory stack. After all the slots
IIII
are filled, then the cards will go to the vacancies available at the end of the list.
B) Output Mode 2 – Timing 1 to 60 seconds:
2) Press BELL button to select output mode 2.
....
Response :
LED 2 is ON. After 2 seconds, the system confirms the selection with 2 beeps.
3) Press BELL button once to start the time counting.
....
Response
:
Counting from 1 second to 60 seconds with 1 second and 1 short Beep per step. The
........................
5 indicator LEDs act as timer indicator from 1 to 5 seconds in the 1st round counting,
........................
and 6 to 10 seconds in the 2nd round ….. and so on, until 60 seconds.
4) Press BELL button again to stop the counting when the desired time reaches.
....
Response
:
2 Beeps confirms the time and the counting LED stops at its position
....
Note
: If it is not the time desired, repeat procedures
(3)
&
(4)
for a new counting.
5) Read Master Card 1 Time to exit Programming Mode.
....
Response
:
2 Beeps confirm reader back to normal operation.
13
Exit
Programming Mode
Stop
Time Counting
Start
Time Counting
Select
Output Mode 2
Read Master Card 3 Times
Set System in Feature Group 3
5
4
3
2
1
3) Read Master Card 1 Time to exit Programming Mode.
....
Response
:
2 Beeps confirm reader back to normal operation.
A) Output Mode 1 – Start / Stop (Toggle):
2) Press BELL button to select output mode 1.
....
Response
:
LED 1 is ON. After 2 seconds, the system confirms the selection with 2 beeps.
Exit
Programming Mode
Select
Output Mode 1
Read Master Card 3 Times
Set System in Feature Group 3
3
2
1
III ) SET OUTPUT MODE FOR DOOR LOCK -- Feature Group 3
The operation of the door lock output can be set to Start/Stop mode or 1 second to 60 seconds
Timing Mode. The ex-factory setting is 2 seconds.
Output Mode 1
– Start / Stop (Toggle)
Output Mode 2
– Timing 1 to 60 seconds (Door lock striking time)
Procedures
1) Read Master Card 3 Times to set system to Feature Group 3 – Set Output Mode for Door
....
Lock.
....
Response
:
Status LED (blue) starts to flash during programming mode and group LED 3 is ON.
........................
After 2 seconds, the system confirms the selection with 2 beeps and the group LED
........................
1 & 2 flashing for the two output modes available.
5. Paul
4. -- (Slot)
4. Alan
3. -- (Slot)
3. Nancy
2. Tracy
2. Tracy
1. John
1. John
After
Before
5. Paul
6.
-- (Vacancy)
6.
-- (Vacancy)
Example
: An User list before and after deleting Nancy and Alan’s user cards, there are 2 slots (3
.................
& 4) left.
This is the programming manner of putting three new user cards into
the system with slots, the 1st one goes to the 1st slot (#3), the 2nd one
goes to the 2nd slot (#4) and the 3rd one goes to the vacancy (#6)
available at the end of the list.
