background image

Self-Contained 

Access Control Reader

AR-2808

User Manual

 

 

 

AEI PROTECT-ON SYSTEMS LIMITED

www.apo-hk.com

VERSION: 01/2015

FCC STATEMENT

Caution:

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate 

this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.

NOTE:

This  equipment  has  been  tested  and  found  to  comply  with  the  limits  for  a  Class  B  digital  device,  pursuant  to  Part  15  of  the  FCC 

Rules.  These  limits  are  designed  to  provide  reasonable  protection  against  harmful  interference  in  a  residential  installation.  This 

equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, 

may  cause  harmful  interference  to  radio  communications.  However,  there  is  no  guarantee  that  interference  will  not  occur  in  a 

particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off 

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

OR-ZS-805

Содержание OR-ZS-805













Отзывы: