ORiNG TES-3080-M12 Series Скачать руководство пользователя страница 12

Страница: 12 / 111

TES-3080-M12(-BP2) User Manual

ORing Industrial Networking Corp

Instead of screwing the screws in all the way, it is advised to leave a space of about
2mm to allow room for sliding the Switch between the wall and the screws.

3.2 Wiring

7. You should separate input wiring from output wiring

8. It is advised to label the wiring to all devices in the system

ATTENTION

1. Be sure to disconnect the power cord before installing and/or wiring your

switches.

2. Calculate the maximum possible current in each power wire and

common wire. Observe all electrical codes dictating the maximum

current allowable for each wire size.

3. If the current goes above the maximum ratings, the wiring could

overheat, causing serious damage to your equipment.

4. Use separate paths to route wiring for power and devices. If power wiring

and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

5. Do not run signal or communications wiring and power wiring through the

same wire conduit. To avoid interference, wires with different signal

characteristics should be routed separately.

6. You can use the type of signal transmitted through a wire to determine

which wires should be kept separate. The rule of thumb is that wiring

sharing similar electrical characteristics can be bundled together

WARNING

Do not disconnect modules or wires unless power has been switched off or

the area is known to be non-hazardous. The devices may only be connected

to the supply voltage shown on the type plate.

Содержание TES-3080-M12 Series
















































































































Результаты поиска

Содержание TES-3080-M12 Series

Отзывы:

Бренды по названию

Популярные бренды

ORiNG TES-3080-M12 Series, Руководство пользователя

Результаты поиска

Содержание TES-3080-M12 Series

Отзывы:

Бренды по названию

Популярные бренды