ORiNG IES-3162GC Series Скачать руководство пользователя страница 11

Страница: 11 / 104

IES-3162GC

User’s Manual

ORing Industrial Networking Corp

IES-3162GC

1. LED for PWR. When the PWR UP, the green led will be light on

2. LED for PWR1. When the PWR2 links, the green led will be light on.

3. LED for PWR2. When the PWR2 links, the green led will be light on.

4. LED for R.M (Ring master). When the LED light on, it means that the switch is the ring

master of Ring.

5. LED for Ring. When the led light on, it means the Ring is activated.

6. LED for Fault. When the light on, it means Power failure or Port down/fail.

7. Console port (RJ-45)

8. Reset button. Push the button 3 seconds for reset; 5 seconds for factory default.

9. 1000Base-X COMBO SFP Port Link/Act LED

10. 1000Base-T gigabits Ethernet port COMBO 1000Base-X Fiber port on SFP

11. 10/100/1000 Base-T(X) Ethernet ports Link LED

12. 10/100/1000 Base-T(X) Ethernet ports Act LED

13. 10/100/1000 Base-T(X) Ethernet ports

Содержание IES-3162GC Series









































































































Результаты поиска

Содержание IES-3162GC Series

Отзывы:

Похожие инструкции для IES-3162GC Series

Бренды по названию

Популярные бренды

ORiNG IES-3162GC Series, Руководство пользователя

Результаты поиска

Содержание IES-3162GC Series

Отзывы:

Похожие инструкции для IES-3162GC Series

Бренды по названию

Популярные бренды