Orbitalum REB 14 страница 8 Скачать руководство пользователя

Страница: 8 / 40

1 Notes on safety

Operating instructions REB 6, REB 14, REB 20

(06.10)

MT_REB 6_REB 14_REB 20_BA_04_790093762_02.doc

orbitalum tools

gmbh

1.3

Working with safety in mind

"Make your contribution to safety in the workplace."



Report any unusual behavior of the machine to the person in charge

immediately.



Always work with safety in mind.



Wear safety goggles and safety gloves when working with the REB.



Tie up long hair (snood-type cap); do not wear any wide clothing.

Attention:

jewelry and ties can get caught by rotating parts.



Keep hands away from the tools during processing.



Switch off the REB after each working cycle and allow the machine to come

to a stop.



REB (E): Disconnect the REB from power supply before performing any

cleaning, maintenance or repair work and allow the machine to come to a
stop.



Do not carry the electric tool holding it at the cable and do not use it to pull

the plug out of the socket. Protect the cable against heat, oil and sharp
edges (chips).



REB (D): Shut down the compressed air supply before carrying out any

maintenance work or cleaning the REB and allow the machine to come to a
stop.



Do not use the REB in areas subject to explosion hazards.



Pay attention to the surroundings. Do not use any electric tools in a damp

or wet area. Make sure to have good illumination. Do not work near
combustible liquids or gases.

Danger of being injured on hands!

Sharp cutting edges and chipping.



Keep hands away from the tools during processing.



Wear safety gloves.

WARNING

Содержание REB 14









































Результаты поиска

Содержание REB 14

Отзывы:

Похожие инструкции для REB 14

Бренды по названию

Популярные бренды

Orbitalum REB 14, Руководство по эксплуатации

Результаты поиска

Содержание REB 14

Отзывы:

Похожие инструкции для REB 14

Бренды по названию

Популярные бренды