Orbit Merret OM 652UC Скачать руководство пользователя страница 44

Страница: 44 / 64

INSTRUCTIONS FOR USE

OM 652UC

6.3

Setting „PROFI“ - OUTPUTS

6.3.1a

Selection of mode of output L 1

6.3.1b

Selection of mode of output L 2

CHANNE.

SERVIC.

OUTPUT.

LIMITS

AN. OUT.

DATA

DISP.

INPUT

It is possible to set the parameters
of the instrument output signals in
this menu

LIMITS

Setting the type and the
switching of limits

DATA

Setting the type and
the parameters ot data

output

AN. OUT.

Setting the type and
parameters of analog

output

DISP.

Setting the display
brightness

INPUT

SERVIC.

OUTPUT

CHANNE.

LIMITS

AN. OUT.

DATA

DISP.

LIM. 1

LIM. 2

HYSTER.

C. -PULS.

DEF

HYS. L.1

LIM. L.1

TIM. L.1

MOD. L.1

TYP. L.1

MOD. L.1

Mode of limit 1

HYSTER.

Standard mode - limit,
hysteresis and delay

C. -PULS.

Automatic clearing of
counter to preset value

and generate an impulse of the length
set in “TIM.L.1”

Setting is available only for LIM 1

INPUT

SERVIC.

OUTPUT

CHANNE.

LIMITS

AN. OUT.

DATA

DISP.

LIM. 2

LIM. 1

HYSTER.

ON RUN

DEF

HYS. L.2

LIM. L.2

TIM. L.2

MOD. L.2

TYP. L.2

MOD. L.2

Mode of limit 2

HYSTER.

Standard mode - limit,
hysteresis and delay

ON RUN

Relay is switched on/
off if the stopwatch is

running

Setting is available only for LIM 2

SETTING

proﬁ

Содержание OM 652UC

































































Результаты поиска

Содержание OM 652UC

Отзывы:

Похожие инструкции для OM 652UC

Бренды по названию

Популярные бренды

Orbit Merret OM 652UC, Инструкция по эксплуатации

Результаты поиска

Содержание OM 652UC

Отзывы:

Похожие инструкции для OM 652UC

Бренды по названию

Популярные бренды