Orban OPTIMOD-FM 8700, Руководство по эксплуатации

Страница: 218 / 390

3-48
OPERATION ORBAN MODEL 8700i
around the pilot. A spectrum analyzer will reveal that, in fact, the pilot is
protected by at least 60 dB in this 500 Hz wide area of the spectrum.
Multiplex Offset (Multiplex Power Offset) operates only when the ITU-412 multiplex
power controller is activated (and is thus irrelevant to users in countries that do not
enforce this standard). The control introduces a fixed loss before the FM analog
peak limiting chain. If the
M
ULTIPLEX
P
OWER
T
HRESHOLD
control (in the I
NPUT
/O
UTPUT
/
U
TILITIES
screen) is set to 0 , the M
ULTIPLEX
P
OWER
O
FFSET
control produces the same
amount of loss (in dB) as this control’s setting. Resetting the M
ULTIPLEX
P
OWER
T
HRESHOLD
control away from 0 will change the loss. (For example, setting the
M
ULTIPLEX
P
OWER
T
HRESHOLD
control to +3 will cause the loss to decrease by 3 dB.)
The M
ULTIPLEX
P
OWER
T
HRESHOLD
control can only introduce loss, never
gain.
Regardless of the setting of the M
ULTIPLEX
P
OWER
T
HRESHOLD
and
M
ULTIPLEX
P
OWER
O
FFSET
controls, the resulting gain offset can never be
larger than 0 dB.
The M
ULTIPLEX
P
OWER
O
FFSET
control’s purpose is to reduce unnatural loudness varia-
tions that the multiplex power controller might produce. These can occur because
the ITU specification does not call for psychoacoustic weighting. The Optimod does
not force the multiplex power controller to dynamically produce all of the required
gain reduction (which could vary widely, depending on the program material). In-
stead, the
M
ULTIPLEX
P
OWER
O
FFSET
control produces most of the gain reduction. The
gain reduction produced by the control is, of course, unchanging and cannot intro-
duce audible artifacts.
The ideal dynamic gain reduction for the multiplex power controller is 2 to 3 dB
with typical program material. However, the actual gain reduction will vary widely
depending on whether the underlying processing preset is “loud” or “quiet.” There-
fore, the appropriate setting of the
M
ULTIPLEX
P
OWER
O
FFSET
control depends
strongly on what preset is in use. Accordingly, each preset has its own setting of the
M
ULTIPLEX
P
OWER
O
FFSET
, which is a processing parameter like any other in a given
preset. Hence, adjustments that affect the multiplex power controller appear in two
independent places in the Optimod: The
M
ULTIPLEX
P
OWER
T
HRESHOLD
control is a sys-
tem setup control, while the
M
ULTIPLEX
P
OWER
O
FFSET
is part of the on-air preset .
Depending on the preset, the M
ULTIPLEX
P
OWER
O
FFSET
control’s setting can vary
from 0 dB (no effect) to as much as –16 dB. If you customize a preset in any way (in-
cluding using
L
ESS
-M
ORE
) , you may wish to trim the M
ULTIPLEX
P
OWER
O
FFSET
for
that preset so that the multiplex power controller produces 2-3 dB of indicated gain
reduction with typical program material. This will achieve the maximum on-air
loudness that complies with the ITU standard while minimizing the potential for un-
natural and audibly disturbing loudness inconsistencies caused by the operation of
the multiplex power controller.
For more information on the multiplex power controller, refer to ITU-R Multiplex
Power Controller on page 3-83.
Bass Clip Mode sets the operation of the bass clipper to H
ARD
, LL H
ARD
, M
EDIUM
, or
S
OFT
. LL HARD
IS
not available in MX presets because reducing the ~260 ms delay of
these presets by 4 ms would have no practical advantage.