manualshive.com logo in svg

OrangeRx TX6i, Инструкция по эксплуатации

Поделиться
Скачать
OrangeRx TX6i Скачать руководство пользователя страница 2

2

6 CHANNEL TRANSMITTER
DIGITAL PROPORTIONAL RADIO
CONTROL SYSTEMPROGRAMABLE SYSTEM

Introduction

Thank you for purchasing our product, an ideal radio system for beginners or experienced users 
alike. Read this manual carefully before operation in order to ensure your safely and the safely of 
others or the safe operation of your system. If you encounter any problem persists, contact your 
local deal or visit our service and support website for 

www.hobbyking.com

Safely 

1. Safely Symbols

Pay close attention to the following symbols and their meaning. Failure to follow these warning 
could cause damage, injury or death.

DANGER 

– Not following these instructions may expose the user to serious injuries or death

WARNING

 – Not following these instructions may expose the user to serious injuries

ATTENTION

 – Not following these instructions may expose the user to minor injuries and 

even to serious injuries

Do not use at night or during a lightening storm, as bad weather will adversely affect the 

control of your system

Make sure that the motors are all moving the same direction as the operating direction

The shutdown sequence: 1. Disconnect the receiver battery 2. Switch off the transmitter. 

Failure following this sequence may result in uncontrolled movement and damage to the 

system.

Do not use the product when visibility is limited

Interference may cause loss of control. To ensure the safely, do not operate in the following-

places:

Near any site where other radio control activities may occur

Near high power lines or communication broadcasting antennas

Near any site where overcrowded and traffic congestion

On water or on boats and ships

Do not use this product when you are tired, uncomfortable or under the influence of alcohol or 

drugs.

Never grip the transmitter antenna during operation. It significantly degrades signal quality 

and strength and may cause loss of control

Safety guide

PROHIBITED

MANDATORY

Содержание TX6i

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды