Oracle ZFS Скачать руководство пользователя

Страница: 63 / 176

NIC/HBA Options

This table describes NIC/HBA PCIe card options for standalone and cluster configurations.

Mktg Part Number

Description

Mfg Part Number

SGX-SAS6-INT-Z

8-port 6Gb/s SAS-2 internal HBA

7054001

SG-XPCIE2FC-QF8-Z

2-port 8Gb FC HBA

371-4325-02

SG-XPCIESAS-GEN2-Z 2-port SAS (x4) external HBA

F375-3609-03

7105394

2-port SAS (x4) external HBA for EU countries 7059331

X4446A-Z-N

4-port GigE UTP

7054739

X4242A

2-port CX2 4xQDR, HCA

594-6776-01

X1109A-Z

2-port 10GbE SFP+ NIC

7051223

X2129A

XCVRm 850NM, 1/10GPS, Short Reach, SFP

7015839

X5562A-Z

10GbE/1GbE SFP+ Transceiver, LR

594-6689-01

PCIe Options

The 7420 controller has ten PCIe slots. This table describes base and optional PCIe card slots for
standalone and cluster configurations.

Note

: The 7420 M2 reserves slot 0 for a SAS-2 internal HBA, and slots 1 and 8 for two SAS-2

external HBAs.

Slot

Mfg Part Number

Description

Max

Note

7054001

8-port 6Gb/s SAS-2 internal
HBA

Slot 0 of the 7420 M2 is reserved for the SAS-2 internal HBA

371-4325-02

8Gb 2-port FC HBA

Optional FC target or initiator (Backup) for the 7420 controller

7051223

2-port optical 10GbE NIC

Optional recommended front-end for the 7420 controller

7054739

4-port copper NIC

Optional recommended front-end for the 7420 controller

F375-3609-03
(7059331 for EU
countries)

2-port SAS external HBA

Base configuration (2 minimum)

F375-3609-03
(7059331 for EU
countries)

2-port SAS external HBA

Additional optional back-end

7054739

4-port copper NIC

Optional recommended front-end

7420

Chapter 1 • Introduction

Содержание ZFS

















































































































































































Результаты поиска

Содержание ZFS

Отзывы:

Похожие инструкции для ZFS

Бренды по названию

Популярные бренды

Oracle ZFS, Руководство по установке

Результаты поиска

Содержание ZFS

Отзывы:

Похожие инструкции для ZFS

Бренды по названию

Популярные бренды