Oracle ZFS Скачать руководство пользователя страница 55

Страница: 55 / 176

Attached Storage

The 7320 single and cluster controller configurations allow a single chain of one to six

disk

shelves

. Any combination of disk-only and Logzilla-capable shelves may be combined within

the chain in any order. The cabling configurations are unchanged. Half-populated shelf
configurations are not supported.

See Also

■

Controller Details

■

Disk Shelf Overview

■

Disk Shelf Maintenance Procedures

7420

7420 Hardware Overview

Use the information on this page as a preparation reference for servicing replaceable
components of 7420 controllers.

Refer to the following for procedural instructions:

■

Controller Tasks - replace system controller components

■

Disk Shelf Tasks - replace disk shelf components

Appliance Overview

The Sun ZFS Storage 7420 Appliance consists of a standalone storage controller, or two storage
controllers in a high-availability cluster configuration, and one to 36 disk shelves. The following
table describes the 7420 configuration options:

Note

: 7420 M2 controllers cannot be clustered with 7420 controllers.

Product ID

Mktg Part
Number

CPU

DIMMs

Readzilla

Boot Drive

Mfg Part Number

7420 M2 7107089 4x8-core, 2.0GHz 8GB, 16GB

1.6TB SAS

900GB SAS

7075466

7420 M2 7107090 4x10-core,

2.40GHz

8GB, 16GB

1.6TB SAS

900GB SAS

7075470

7420

7100566 4x8-core, 2.0GHz 8GB, 16GB

512GB SATA

500GB SATA

7014572

7420

7100568 4x10-core,

2.40GHz

8GB, 16GB

512GB SATA

500GB SATA

7014573

7420

Chapter 1 • Introduction

Содержание ZFS

















































































































































































Результаты поиска

Содержание ZFS

Отзывы:

Oracle ZFS, Руководство по установке, Страница: 55 / 176

Результаты поиска

Содержание ZFS

Отзывы: