Oracle Sun ZFS Скачать руководство пользователя страница 51

Страница: 51 / 146

Cluster Base Options

This table describes 7420 cluster base configurations.

Mktg Part Number

Description

Mfg Part Number

TA7420-26AR00HA

S7420, no DIMMs, 2x1.86GHz-6C, Cluster

597-0795-01

TC7420-28AR00HA

S7420, no DIMMs, 2x2.00GHz-8C, Cluster

597-0792-01

7100566

S7420, no DIMMs, 4x2GHz-8C, Cluster

7014572

7100568

S7420, no DIMMs, 4x2.40GHz-10C, Cluster 7014573

NIC/HBA Options

This table describes NIC/HBA options for 7420 single and cluster configurations.

Mktg Part Number

Description

Mfg Part Number

SG-XPCIESAS-GEN2-Z

2-port External Sun Thebe SAS (x4) HBA, PCIe F375-3609-03

SG-XPCIE2FC-QF8-Z

2-port FC HBA, 8Gb, PCIe

594-5684-01

X4446A-Z

4-port PCIe Quad GigE UTP

594-4024-01

X4237A

2-port 4X IB HCA PCIe

594-5862-02

X1109A-Z

2-port 10Gig SFP+ NIC, PCIe

594-6039-01

X2129A

XCVRm 850NM, 1/10GPS, Short Reach, SFP

594-6508-01

PCIe Options

This table describes the supported single and clustered PCIe configuration option summary for
7420.

Slot Type

Sun Part
Number

Description

Note

PCIe 371-4325-01 8Gb DP FC HBA

Optional FC Target or Initiator (Backup)

PCIe 375-3609-02 DP SAS-2 HBA

Base Configuration

PCIe 375-3609-02 DP SAS-2 HBA

Additional Optional Back-end

PCIe 375-3481-01 QP Copper NIC

Optional Recommended Front-end

PCIe 371-4325-01 8Gb DP FC HBA

Optional FC Target or Initiator (Backup)

PCIe 375-3606-01 Infiniband HCA

Optional Recommended Front-end

7420

Chapter 2 • Hardware Maintenance

Содержание Sun ZFS



















































































































































Результаты поиска

Содержание Sun ZFS

Отзывы:

Oracle Sun ZFS, Руководство по обслуживанию, Страница: 51 / 146

Результаты поиска

Содержание Sun ZFS

Отзывы: