Oracle Netra SPARC S7-2 Скачать руководство пользователя страница 61

Страница: 61 / 102

Connecting Cables

Perform the following tasks to connect and configure the network and serial ports before you

apply power to the server.

Step

Description

Links

Review the available connections.

“Available Connections” on page 61

Cable the SP.

“Cable the SP” on page 64

“SER MGT Port” on page 66

“NET MGT Port” on page 67

“USB Ports” on page 69

Cable the Ethernet ports.

“Cable the Ethernet Ports” on page 64

“10 Gigabit Ethernet Ports” on page 68

(Optional) Connect other data cables.

“Connect Other Data Cables” on page 65

“USB Ports” on page 69

Documentation for your PCIe cards

Related Information

■

“Understanding the Server” on page 11

■

“Confirming Specifications” on page 17

■

“Preparing for Installation” on page 27

■

“Installing the Server” on page 31

■

“Powering On the Server for the First Time” on page 71

Available Connections

Before applying power to the server, provide connectivity to the SP and server.

Connecting Cables

Содержание Netra SPARC S7-2







































































































Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды

Oracle Netra SPARC S7-2, Руководство по установке

Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды