Oracle Netra SPARC S7-2 Скачать руководство пользователя страница 64

Страница: 64 / 102

Cable the SP

Related Information

■

“Identifying Ports” on page 65

■

“Rear Panel Components (Installation)” on page 15

Cable the SP

The SP is integrated into the motherboard. Connection to the SP is through the SER MGT port

on the rear of the server.

Determine which of these connections works in your environment and establish

the connection:

■

SER MGT port

■

NET MGT port

■

USB keyboard and mouse

You can configure any combination of these connections. See

“Available

Connections” on page 61

Related Information

■

“Available Connections” on page 61

■

“Cable the Ethernet Ports” on page 64

■

“Connect Other Data Cables” on page 65

■

“Identifying Ports” on page 65

■

“Rear Panel Components (Installation)” on page 15

Cable the Ethernet Ports

Once the server is running the OS, these connections provide Ethernet access to the server. See

“10 Gigabit Ethernet Ports” on page 68

Note -

The Oracle ILOM sideband management feature enables you to access the SP using

one of these Ethernet ports. Refer to the

Oracle ILOM Administor's Guide for Configuration

and Maintenance For Release 3.2.x

http://www.oracle.com/goto/ilom321/docs

for

instructions.

Netra SPARC S7-2 Server Installation Guide • January 2017

Содержание Netra SPARC S7-2







































































































Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды

Oracle Netra SPARC S7-2, Руководство по установке

Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды