Oracle Netra SPARC S7-2 Скачать руководство пользователя страница 71

Страница: 71 / 102

Powering On the Server for the First Time

These topics include instructions for powering on the server for the first time and configuring

the Oracle Solaris OS.

Step

Description

Links

Review power requirements.

“Electrical Specifications” on page 18

“Input Power Information” on page 19

“Overcurrent Protection Requirements” on page 20

“DC Power Source, Power Connection, and Grounding

Requirements” on page 21

Connect the chassis grounding wire (optional for

AC input power).

“Connect the Chassis Ground Wire” on page 72

Connect power cords.

“Connect AC Power Cords” on page 74

“Assembling and Connecting DC Power Cords” on page 75

Connect a serial terminal device or terminal

server to the SER MGT Port.

“Connect a Terminal or Emulator to the SER MGT

Port” on page 81

“Oracle ILOM System Console” on page 82

Power on the server and start the Oracle ILOM

system console.

“Power on the Server for the First Time” on page 83

“Configure the Preinstalled OS” on page 86

Configure the preinstalled OS, or install a fresh

OS.

“Configure the Preinstalled OS” on page 86

“Reach a State to Install a Fresh OS (Oracle ILOM Web

Interface)” on page 88

Set the configuration parameters for the Oracle

Solaris OS.

“Oracle Solaris OS Configuration Parameters” on page 91

8. (Optional)

Configure the NET MGT port to use a static IP

address.

“Assign a Static IP Address to the NET MGT Port” on page 92

9. (Optional)

Activate Oracle Auto Service Request for the

server.

“Oracle Auto Service Request Software Activation” on page 94

Powering On the Server for the First Time

Содержание Netra SPARC S7-2







































































































Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды

Oracle Netra SPARC S7-2, Руководство по установке

Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды