Oracle Netra SPARC S7-2 Скачать руководство пользователя страница 86

Страница: 86 / 102

Installing the OS

Installing the OS

Use these topics to either configure the preinstalled OS or use an alternative OS.

■

“Configure the Preinstalled OS” on page 86

■

“Reach a State to Install a Fresh OS (Oracle ILOM CLI)” on page 87

■

“Reach a State to Install a Fresh OS (Oracle ILOM Web Interface)” on page 88

Related Information

■

“Oracle Solaris OS Configuration Parameters” on page 91

Configure the Preinstalled OS

Determine which OS you will use.

■

If you plan to use the preinstalled OS, proceed to step 2.

■

If you do not plan to use the preinstalled OS, go to

“Reach a State to Install

a Fresh OS (Oracle ILOM CLI)” on page 87

“Reach a State to Install a

Fresh OS (Oracle ILOM Web Interface)” on page 88

When prompted, follow the onscreen instructions for configuring the Oracle

Solaris OS on your host.

You are prompted to confirm the configuration several times, enabling confirmation and

changes. If you are not sure how to respond to a particular value, you can accept the default

and make future changes when the Oracle Solaris OS is running. See

“Oracle Solaris OS

Configuration Parameters” on page 91

for a description of the Oracle Solaris OS parameters

you must provide during initial configuration.

Log in to the server.

You can now enter Oracle Solaris OS commands at the prompt. For more details, refer to the

Oracle Solaris 11 OS man pages and documentation at:

http://www.oracle.com/goto/solaris11/docs

Related Information

■

“Connect AC Power Cords” on page 74

Netra SPARC S7-2 Server Installation Guide • January 2017

Содержание Netra SPARC S7-2







































































































Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды

Oracle Netra SPARC S7-2, Руководство по установке

Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды