Oracle Netra SPARC S7-2 Скачать руководство пользователя страница 74

Страница: 74 / 102

Connect AC Power Cords

Related Information

■

“Assemble the DC Input Power Cords” on page 76

■

“Connect DC Power Source” on page 80

■

“Power on the Server for the First Time” on page 83

Connect AC Power Cords

Prepare the power cords by routing them from the AC power source to the server.

Caution -

Do not attach power cables to the power supplies until you have connected the server

to a serial terminal or a terminal emulator (PC or workstation). The server goes into Standby

mode and Oracle ILOM on the SP initializes as soon as a power cable connects a power supply

to an external power source. System messages might be lost after 60 seconds if a terminal or

terminal emulator is not connected to the SER MGT port before power is applied.

Note -

Oracle ILOM signals a fault if both power supplies are not cabled at the same time, since

it will be a nonredundant condition. Do not be concerned with this fault in this situation.

(Optional) Connect the chassis ground studs to earth ground.

See

“Connect the Chassis Ground Wire” on page 72

Route the power cords from the AC power source to the rear of the server.

Netra SPARC S7-2 Server Installation Guide • January 2017

Содержание Netra SPARC S7-2







































































































Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды

Oracle Netra SPARC S7-2, Руководство по установке

Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды