Oracle Netra SPARC S7-2 Скачать руководство пользователя страница 92

Страница: 92 / 102

Assign a Static IP Address to the NET MGT Port

■

“Reach a State to Install a Fresh OS (Oracle ILOM CLI)” on page 87

■

“Reach a State to Install a Fresh OS (Oracle ILOM Web Interface)” on page 88

Assign a Static IP Address to the NET MGT Port

If you plan to connect to the SP through its NET MGT port, the SP must have a valid IP

address.

By default, the server is configured to obtain an IP address from DHCP services in your

network. If the network your server is connected to does not support DHCP for IP addressing,

perform this procedure.

Note -

To configure the server to support DHCP, refer to the Oracle ILOM documentation.

Connect to the Oracle ILOM on the SP using the SER MGT port.

If you are not already connected through the SER MGT port, perform steps as needed in

“Connect a Terminal or Emulator to the SER MGT Port” on page 81

Set the SP to accept a static IP address.

set /SP/network pendingipdiscovery=static

Set 'pendingipdiscovery' to 'static'

Set the IP address for the SP.

■

To change the default IPv4 DHCP property and set property values for a

static IPv4 address, type

IPv4_address

■

To change the default IPv6 DHCP property and set property values for a

static IPv6 address, type

IPv6_address

set /SP/network pendingipaddress=

service-processor-IPaddr

Set 'pendingipaddress' to '

service-processor-IPaddr

Set the IP address for the SP gateway.

set /SP/network pendingipgateway=

gateway-IPaddr

Set 'pendingipgateway' to '

gateway-IPaddr

Set the netmask for the SP.

set /SP/network pendingipnetmask=255.255.255.0

Netra SPARC S7-2 Server Installation Guide • January 2017

Содержание Netra SPARC S7-2







































































































Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды

Oracle Netra SPARC S7-2, Руководство по установке

Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды