Oracle Exadata Storage Server X7-2 EF Скачать руководство пользователя страница 50

Страница: 50 / 90

Install the Cable Management Arm (Optional)

Call Out

Description

Slide-rail latching bracket (used with connector D)

Back slide bar

Oracle Storage Server X7-2 (1U) flat cable covers

Oracle Storage Server X7-2L (2U) round cable covers

Remove the flat cable covers and install the round cable covers.

Lift up on the cable cover handle (the handle is colored green) and open

it 180 degrees to the horizontal position as shown in the following figure

[frames 1 and 2].

Note -

The CMA has three cable covers, two with two hinges (one of which is shown in the

following figure), and one with a single hinge. All three cable covers are shown in the previous

figure.

Oracle Exadata Storage Server X7-2 EF and HC Installation Guide • November 2018

Содержание Exadata Storage Server X7-2 EF



























































































Результаты поиска

Содержание Exadata Storage Server X7-2 EF

Отзывы:

Похожие инструкции для Exadata Storage Server X7-2 EF

Бренды по названию

Популярные бренды

Oracle Exadata Storage Server X7-2 EF, Руководство по установке

Результаты поиска

Содержание Exadata Storage Server X7-2 EF

Отзывы:

Похожие инструкции для Exadata Storage Server X7-2 EF

Бренды по названию

Популярные бренды