Oracle Exadata Storage Server X7-2 EF Скачать руководство пользователя страница 34

Страница: 34 / 90

Safety Precautions

Safety Precautions

This section describes safety precautions you must follow when installing the server into a rack.

Caution -

Leveling feet position

: When unpacking at the installation site, or when repackaging

and moving the rack to a new location, verify that the leveling feet are up before moving the

rack.

Caution -

Stabilize rack

: Deploy the anti-tilt bar on the equipment rack before starting an

installation.

Caution -

The rack shipping brackets are not for use for bracing or anchoring the rack during

seismic events.

Caution -

Equipment loading

: Always load equipment into a rack from the bottom up so that

the rack does not become top-heavy and tip over. Deploy your rack anti-tilt bar to prevent the

rack from tipping during equipment installation.

Caution -

Lifting equipment

: The EF server weighs 22.8 kg (50.2 lbs) and the HC server

weighs 30.5 kg (67.1 lbs). Two people are needed to mount either server into the rack enclosure.

Caution -

Communicate instructions

: When performing a two-person procedure,

communicate your intentions clearly to the other person before, during, and after each step to

minimize confusion.

Caution -

Elevated operating ambient temperature

: If you install the server in a closed

or multi-unit rack assembly, the operating ambient temperature of the rack environment

might be higher than the room ambient temperature. Install the equipment in an environment

compatible with the maximum ambient temperature (Tma) specified for the server. For server

environmental requirements, see

“Environmental Requirements” on page 15

Oracle Exadata Storage Server X7-2 EF and HC Installation Guide • November 2018

Содержание Exadata Storage Server X7-2 EF



























































































Результаты поиска

Содержание Exadata Storage Server X7-2 EF

Отзывы:

Похожие инструкции для Exadata Storage Server X7-2 EF

Бренды по названию

Популярные бренды

Oracle Exadata Storage Server X7-2 EF, Руководство по установке

Результаты поиска

Содержание Exadata Storage Server X7-2 EF

Отзывы:

Похожие инструкции для Exadata Storage Server X7-2 EF

Бренды по названию

Популярные бренды