Oracle Exadata Storage Server X7-2 EF Скачать руководство пользователя страница 86

Страница: 86 / 90

Preparation Checklists

Logistics Checklist Considerations

Yes

N/A Comment

data center? If yes, then do you have a recommended

agency?
Are there any additional security access issues?

Is computer room access available for installation

personnel?

Are laptops, cell phones, and cameras allowed in the

data center?

Does the building have a delivery dock?

Is there a delivery/unpacking/staging area, and is it

protected from environmental elements?

Is the unpacking area air-conditioned to avoid thermal

shock for various hardware components?

Will sufficient moving personnel be available to install

the hardware?

Are you prepared for uncrating and trash removal?

Are there any restrictions on delivery truck length,

width, or height?

Are cardboard boxes and other packing material

allowed in the computer room?

Is there a time constraint on dock access? If yes, then

provide the time constraints.

Is a tail lift required of the delivery carrier to unload the

equipment at the delivery dock?

Will any of the following items be required to place

equipment in the computer room?

■ Stair walkers
■ Lifters
■ Ramps
■ Steel plates
■ Floor covers

Does the delivery carrier require any special equipment,

such as non-floor damaging rollers, transport dollies,

pallet jacks, or fork lifts?

Related Information

■

“Storage Server Physical Specifications” on page 13

■

“Receiving and Unpacking Requirements” on page 14

■

Oracle Exadata Storage Server X7-2 EF and HC Service Manual

■

Oracle Engineered System Safety and Compliance Guide, Compliance Model No.: ESY27

Oracle Exadata Storage Server X7-2 EF and HC Installation Guide • November 2018

Содержание Exadata Storage Server X7-2 EF



























































































Результаты поиска

Содержание Exadata Storage Server X7-2 EF

Отзывы:

Похожие инструкции для Exadata Storage Server X7-2 EF

Бренды по названию

Популярные бренды

Oracle Exadata Storage Server X7-2 EF, Руководство по установке

Результаты поиска

Содержание Exadata Storage Server X7-2 EF

Отзывы:

Похожие инструкции для Exadata Storage Server X7-2 EF

Бренды по названию

Популярные бренды