OPW Wireless Petro-Net Modem Скачать руководство пользователя страница 20

Страница: 20 / 32

www.opwglobal.com

Document #:

M00-20-7074 Rev. 005

Page 20 of 32

4. XTEND Modem Advanced Configuration

This section describes how to configure modems with XTEND Advanced Configurations.

Advanced Modem Configuration is ONLY needed if you have 3 or more modems.

4.1

What You Will Need

A computer with Windows

98, SE, 2000, or XP operating system and an available RS-232 (DB-9) serial com

port is required for XTEND Advanced Configurations.

4.2

Configuration Settings

The Wireless Petro-Net Modem

s are configured at the factory and are ready to install.

You can verify the

configuration using a computer (Windows

98, SE, 2000 or XP) and the software provided. DIP switch settings

#1, #5, #6 ON to configure and run the range test; switch settings #5, #6 ON for OPW normal operation. If the
site has communication interference, change the hopping channel on

both

modems to another channel.

4.3

Installing the Software

Double-

click the “setup_X-CTU.exe” file and follow the prompts of the installation screens. This file is located in

the

software

folder of the MaxStream CD and also under the

downloads

section of the following Web page:

www.maxstream.net/helpdesk/



X-CTU Software

—

MaxStream provides software that can be used to:



Setup

PC serial com ports to communicate with Wireless Petro-Net Modem



Test

Wireless Petro-Net Modem

parameters



Configure

Wireless Petro-Net Modem

parameters

1. Place the auto-ru

nning software CD in your computer’s CD drive.

2. Double-click the

setup_X-CTU.exe

file.

3. Follow the prompts.

The X-CTU software interface is divided into the four (4) following tabs:



PC Settings

—Setup PC serial com ports to interface with the Wireless Petro-Net Modem



Range Test

—Test Wireless Petro-Net Modem

’s range under varying conditions



Terminal

—Read/Set Wireless Petro-Net Modem

parameters and monitor data communications



Modem Configuration

—Read/Set Wireless Petro-Net Modem

parameters

Содержание Wireless Petro-Net Modem

































Результаты поиска

Содержание Wireless Petro-Net Modem

Отзывы:

Похожие инструкции для Wireless Petro-Net Modem

Бренды по названию

Популярные бренды

OPW Wireless Petro-Net Modem, Руководство пользователя

Результаты поиска

Содержание Wireless Petro-Net Modem

Отзывы:

Похожие инструкции для Wireless Petro-Net Modem

Бренды по названию

Популярные бренды