manualshive.com logo in svg

Optimum OPTidrill DH 26GTV, Руководство по эксплуатации, Страница: 27 / 116

Поделиться
Скачать
Optimum OPTidrill DH 26GTV Скачать руководство пользователя страница 27

OPTIMUM

M A S C H I N E N   -   G E R M A N Y

Assembly

Version 1.2.5  dated 2017-03-10

Page 27

Original operating instructions

DH26GTV | DH28GSV | DH32GSV

GB

The ground must be suitable for the geared drill. Pay attention also to the load-bearing 
capacity and evenness of the floor. 

The substructure must be prepared in such a way as to ensure that, if any lubricant is used, 
it cannot penetrate the floor.

Protruding parts - such as the dog, handles, etc. - must be secured, where necessary, by 
means of on-site measures so that persons are not endangered.

Provide enough space for set-up and operating personnel and material transport.

Also bear in mind accessibility for installation and maintenance works.

Ensure adequate lighting is available (minimum value: 500 Lux, measured at the tool tip). In 
the event of a lower level of lighting, additional illumination must be provided, e.g. by means 
of a separate workplace light.

INFORMATION

The mains plug of the geared drill must be freely accessible.

3.3.2 Assembly

WARNING!

Danger of crushing and overturning.
The installation of the geared drill must be performed by at least 2 persons.

INFORMATION

The geared drill is delivered pre-assembled.

3.4

Installation

Check that the geared drill foundation is horizontal with a spirit level. 

Check that the foundation has sufficient load-bearing capacity and rigidity. The total weight 
is: 



 "Total weight [kg]“ on page  21

Place the geared drill on the provided foundation.

Fix the geared drill base to the substructure through the holes pre-drilled for this purpose.

WARNING!

The condition of the underground and the fixing type of the machine foot to the 
underground must be in a way that it can bear the loads of the geared drill. The 
foundation must be level. Check that the geared drill foundation is horizontal with a 
spirit level.

3.5

Fixing

In order to provide for the necessary stability of the geared drill, 

 

it is necessary to firmly connect the geared drill with its foot to the ground. We recommend that 
you use shear connector cartridges or heavy-duty anchors.

Fix the foot of the geared drill to the ground with the holes pre-drilled for this purpose.

Содержание OPTidrill DH 26GTV





















































































































Отзывы:

Нет отзывов