Optics ODM- 88 Скачать руководство пользователя страница 23

Страница: 23 / 78

USER MANUAL

DVI MATRIX ROUTER : ODM-88

ODM-88 Manual

Page 23

1) Press

FUNCTION

key

– LCD will display EDID Read/Write:

=========Function Mode========

EDID Read/Write

IN : 1.2.3.4.5.6.7.8
OUT: 1.2.3.4.5.6.7.8

Configure as shown below:

=========Function Mode========

EDID Read/Write

IN : 1.2.3.4.5.6.7.8
OUT: 1.2.3.4.5.6.7.8

[Note] If a source is connected to two or more different displays, assigning the lower

resolution EDID to Input port EEPROM is highly recommended. Assigning higher

resolution will show

‘OUT OF RANGE’.

Press

ENTER

to save.

[Note] EDID setting is valid until a new EDID setting is processed - even though the

ODM-88 is powered on and off repeatedly.

To configure Input-Output, press

CREATE

; current Input-Output configuration will

be displayed.

========= Create Mode ========

I: 1 2 3 4 5 6 7 8 N



O: 1 2 3 4 5 6 7 8 M

Where

ot defined for the monitoring,

Press Input button

(Green LED is on)

– LCD displays:

========= Create Mode ========

Input Channel NUM.: 1

Out: 1

New:

Press Output 1 and 4 (number

1 and 4)

as the selected outputs for the given Input.

Press

ENTER

key and then turn back to the

user mode

[Note] Specific Input can be connected to multiple Output channels. However, one Output
channel cannot share multiple Input channels.

Repeat above process 4 to 5 for other Input channels.

Press

PREVIEW

key to review newly saved Input-Output configuration;

========= Preview Mode ========

I: 1 2 3 4 5 6 7 8 N



O: 1 2 3 4 5 6 7 8 M

[Note] Pressing ENTER key completes the Input-Output configuration.

Содержание ODM- 88















































































Результаты поиска

Содержание ODM- 88

Отзывы:

Бренды по названию

Популярные бренды

Optics ODM- 88, Руководство пользователя

Результаты поиска

Содержание ODM- 88

Отзывы:

Бренды по названию

Популярные бренды