manualshive.com logo in svg

Optex ELITE PRO, Инструкция по эксплуатации, Страница: 20 / 24

Поделиться
Скачать
Optex ELITE PRO Скачать руководство пользователя страница 20

Preface

Installation

Troubleshooting

Specifications

20

Procedures

Color

Indicator diagram Status

When installed on approach side

When installed on swing side

Error or warning 

generated

Green

Blinking (0.5 s 

intervals)

Signal saturation (*1)

0.5 s

Solid/off (0.5 s only)

ANSI 500 ms OFF

When solid Green during stand-by, the indicator will go off for 0.5 s 

when the door controller test signal is input, and then light up Green 

again

Green

Blinking fast (0.1 s 

intervals)

Sensor failure (self-monitoring) or sensitivity too low

Orange

Blinking (0.5 s 

intervals) 

Setting error (includes auto configuration incomplete (at initial startup))

Orange/Green

Blinking among col-

ors (0.5 s intervals)

Position error (includes shift to auto configuration when door is not fully 

closed)

Red

0.7 s

2 times

Blinking twice (0.1 s 

interval) (0.7 s unlit)

Wiring error (*2)

Orange

0.7 s

2 times

Blinking twice (0.1 s 

interval) (0.7 s unlit)

Communication error (*3)

*1:  Includes mounting position too low and wall or other object in detection range. The OA-607 T threshold value angle can be set at depth +5° 

or less.

*2:  One of the wiring errors below on the sensor controller side: Activation output (Yellow wire), stall output (Green wire), test input (Pink wire), 

BodyGuard or motor voltage input (Red wire), close switch input (White wire).

*3:  Connected with sensor cable, but communication is unstable. Sensor cable may be disconnected or connector insertion may be loose.

 

z

OC-907C T operation indicator

Operation indicator

(Left corresponds to left side connector 

and right to right side connector)

Procedures

Color

Indicator diagram Status

Meaning

Before initial setup Orange

Blinking (0.5 s 

intervals)

Configuration error within setting error

During initial setup Orange

Blinking (0.5 s 

intervals)

Auto configuration abnormally completed

During background 

learning

Red/Yellow

Blinking among col-

ors (0.1 s intervals)

Auto area learn Incomplete

When auto area learn is incomplete at activation, or has failed for some 

reason

Error or warning 

generated

Green

Blinking (0.5 s 

intervals)

Signal saturation

0.5 s

Solid/off (0.5 s only) When solid Green during stand-by, the indicator will go off for 0.5 s 

when the door controller test signal is input, and then light up Green 

again

Green

Blinking fast (0.1 s 

intervals)

Sensor failure (self-monitoring) or sensitivity too low

Orange

Blinking (0.5 s 

intervals)

Setting error (includes auto configuration incomplete (at initial startup))

Orange/Green

Blinking among col-

ors (0.5 s intervals)

Position error (includes shift to auto configuration when door is not fully 

closed)

Содержание ELITE PRO

























Отзывы:

Нет отзывов