Optex ELITE PRO Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 24

Optex ELITE PRO Скачать руководство пользователя страница 18

Preface

Installation

Troubleshooting

Specifications

18

Automatic settings and auto area learn

Execute the following with the function switch on the OA-607 T front or with the setting app.

Auto configuration:
ELITE PRO has an advance learning system that can recognize the following system configuration and status and set the related parameters

properly and automatically for easy and quick settings.

After parameter settings, it automatically starts auto area learn to setup the area for each OA sensor heads to complete auto configuration.
● Test input (Enable or Disable)
● Test input polarity (High or Low)
● Stall output (N.O. or N.C.)
● Sensor side (Approach or Swing side)
● Hinge side (Right Hand or Left hand)

Auto area learn:

OA has a learning system that check the condition of floor surface for door opening angles.

OA-607 T function switch operation

Press front function switch

Check in advance that the door is fully closed.

WARNING

WARNING

The door opens and closes automatically, so move away from it after starting.

Procedure

Conditions

for opera-

tion

Operation

Result

Operation

Indicator

OA-607 T operation indicator

OC-907C T operation indicator

During initial

setup

Door fully

closed

Hold down the front

function switch

(more than 2 s)

Auto configuration start

Blinking fast in Orange (0.1 s intervals) = Auto configuration

start

Execute auto configuration

The door will open and close two or

three times automatically (*1).

Solid Green after normal completion

= Setup complete (stand-by)

Upon failure, after checking the wir-

ing, execute auto configuration again.

If there is no problem with the wiring,

manual setting from a smart device is

also possible.

After installation is complete, leave

the power on for at least 30 minutes

in order to achieve stable operation

during use.

Upon failure:

Blinking Orange (0.5 s intervals)

(= Setting error)

When

adjusting

the angle

or changing

the settings

after auto

configura

-

tion

None in

particular

Briefly press the

front function switch

(more than 0.3 s, no

more than 2 s) once

Start auto area learn only

Blinking fast in Yellow (0.1 s intervals) = Start auto area learn only

Execute auto area learn only

Solid Green after normal completion = Setup complete (stand-by)

Other

If the door is prevented from opening by an obstacle or the

power is cut just after auto area learn is complete: blinking

alternately Yellow and Red (0.1 s intervals) = Incomplete

*1: Twice or three times in accordance with the door controller signal input setting (combination of stall signal and test signal, etc.) during auto configuration.

NOTE

NOTE

Before executing auto configuration, the connection between the door controller and the OC-907C T sensor controller must be complete.

Auto configuration must be started with the door fully closed. Otherwise, a setting error will be generated.

«
...
16
17
18
19
20
...
»

Содержание ELITE PRO

























Отзывы:

Нет отзывов