Onicon F-4600 Series Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 37

background image

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

F-4600 With LCD Flow Meter Manual 06/18 - 2020-3 / 35874

Page

11

Slide calculator

enclosure to

remove from

sensor mounting

brackets

Slide Enclosure

Mounting Tracks

Retaining

Screw

Retaining

Screw

IMPORTANT NOTE

When installing the meter in a vertical pipe with upward flow, you must rotate the enclosure

back plate 180° when rotating the display 90°. To accomplish this, temporarily remove the 4

cover screws and rotate the backing plate.

i

For ½ - 1” meter sizes the calculator enclosure may be rotated around the axis of the flow sensor
into three different positions. To rotate, temporarily slide the enclosure off the flow sensor
mounting brackets. Remove the two retaining screws and reposition the mounting brackets
as required. Reinstall the enclosure with the display properly oriented for viewing. Mounting
tracks on the back of the enclosure allow for mounting in any orientation.

Orient the ½ - 1” meters as shown below. The meter may be installed with upward or downward
flow in vertical pipes in closed loop pressurized systems. Avoid any installation locations where
the pipe may not be completely full.

Do not orient meter as shown above

Back View

Side View

Meter Sizes ½” to 1”

Preferred Orientation for Horizontal Housing

Side View

«
...
9
10
11
12
13
...
»

Содержание F-4600 Series






































Отзывы:

Нет отзывов

Похожие инструкции для F-4600 Series

Бренд: AccuMASTER Страницы: 2

Бренд: ABQ Industrial Страницы: 15

Бренд: ABQINDUSTRIAL Страницы: 3

Бренд: Oakton Страницы: 4

Бренд: Unipulse Страницы: 129

Бренд: IDEAL Страницы: 11

Бренд: IDEAL Страницы: 16

Бренд: Parkside Страницы: 114

Бренд: Ralston Instruments Страницы: 52

IRmadillo DOC1048R

Бренд: Keit Страницы: 27

Бренд: Keeler Страницы: 54

Бренд: Vigor Equipment Страницы: 12

Бренд: SAT-Kabel Страницы: 12

Бренд: PICO Страницы: 2

DT4120 PS Series

Бренд: Datcon Страницы: 92

Бренд: Kawai Страницы: 72

Бренд: JUMO Страницы: 150

Photo Research PR-810

Бренд: Jadak Страницы: 120

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды