background image

Plenum Box

22 gauge galv.

2HP Commercial Wood Dust Collector Owner’s Manual

O.A.S. 2002

c

5 gallon buckets 12” high (Not supplied with system). Can

be purchased, Part No. SDS050000 or recycled joint

compound buckets or food storage containers can be used.

X.  External Filter Bag Assembly

Tube Filters

16oz. Needle Felted Polyester

1 Micron Filtration

Hose Clamps

Part # - ACB120000

Hose Clamps

Part # - ACB120000

Ring Thimble

Part # - FAZ000000

6’ long - Part # FTS060000

8’ long - Part # FTS080000*

10’ long - Part # FTS100000

*Note: Also available with zipper

bottoms for 9’ ceilings.

1. Connect the plenum to the fan / blower outlet with

3/8” bolts provided. Band clamp tube filters to the

Ring Thimbles on the bottom of the plenum and to

the tops of the 5 gal. buckets.

2. Bolt square to round transition and plenum to

square exhaust transition using (4) 1/2” screws or

5/32” aluminum pop rivets.

Build your own plenum

  Plenum box can be constructed of plywood or metal.

Oneida Air Systems sells 22 gauge galv. plenum boxes.

The filter medium is a 16 ounce polyester felt which has

been singed inside to help release caked dust.

  For the tube style filters, a 12” dia. ring thimble (Part #

FAZ000000) is needed for each filter. The plenum box and

the ring thimbles are suspended above the floor at a height

that will allow for a 5 gallon plastic bucket and tube filter to

fit properly underneath.

  A well sealed plywood box will make a good plenum for

air distribution through the tube filters. Use plywood for the

plenums. Cut 12” dia. holes in the bottom of the box (spaced

2 - 3” apart), so that the ring thimbles fit snugly. The rings

should not be able to slide through the holes. Bend tabs

on Ring Thimble over then apply duct sealant or caulk

around the edge of the ring thimble. Use sheet metal screws

to secure.

  Be sure to remove any sharp edges from the bucket or

ring thimble that may abrade the filter. Slide the filter over

the thimble past the raised bead. Secure with a band clamp.

Slide the bottom of the filter over a five gallon plastic bucket.

Secure with a band clamp or strong bungee (shock cord).

Be sure filter is not loose or moving around when the system

is on. This could lead to wear on the filter.

  With the use of a cyclone pre-separator, the buckets will

not need emptying very often, but do need to be checked

occasionally. Simply lift the bucket, the weight will indicate

how full the bucket has become.

12”

12”

12”

Air

Inlet

Plenum box height - 12” min. Use 3/8” or thicker plywood.

Seal plenum box with silicone.

Note: The number of filters and hole configurations vary.

Check with a sales technician if you have questions.

11

Содержание Super Dust Gorilla 2hp




















Отзывы: